Slitting Rewinding Machineing

Slitting Rewinding Machineing

Slitting machine operating procedures -

First. When the unwinding machine normally replaces the parent roll
1. The machine is wound up and the machine speed is zero. Press the "machine off" button and all drives are turned off.
2. Press and hold the “core release” button to make the chuck exit the empty core, the empty core is placed on the unloading guide, and then the pneumatic ejector will automatically
Empty the core to the unloading position, release the button, and the steel core is to be transported away by the crane.
3. Press the “Coil Snap” button briefly to retract the cylinder rod at the unwinding position to the receiving position.
4. According to the plan, attach the corresponding mother roll to the double-sided tape, and hang the new mother roll into the V-shaped support that supports the parent roll, and hang the empty roll.
core.
5. Press and hold the “Coil Core Clamp” button to make the card head into the new parent roll until the card head positioning pin is in place and release the button. 6. Adjust the length and diameter of the unwinder on the operation screen (correct the input value if necessary), and replace the parent roll.

Slitting Rewinding Machineing

Reasons, countermeasures and effects of BOPP film slitting quality ---

twelve. Interface quality problem (poor interface quality, interface identifier does not match)

2. Interface identifier
Due to the large thickness of the film interface, the film roll for some applications must be properly handled at the interface to avoid unnecessary problems, such as slowing down, increasing the gap between the coating blade, and printing the offset plate. The interface products must be identified as necessary to facilitate customer identification and internal management.
1 The color of the adhesive interface is generally beige, special requirements are used according to the regulations. For example, Shanghai Ziquan requires the use of black adhesive tape; the marking method of the joint position is operated according to the regulations, such as Zhuhai Zhongfu Pearl Film, Shenzhen Ruimei The hot film is required to be marked at the ends of the interface with yellow paper dust protruding from the end of the film roll by about 1 cm; other special marks are operated according to the requirements of the production tribe.
2 Require the slitting workshop to mark the length number of the joint product without special requirements after the length of the label in the length column of the package label, and mark the “buter” mark on the note bar of the computer, and mark “+” on the remark column. Marking, pearl film and imitation paper film and exporting pearl film should indicate the length of each product before and after the joint on the length column of the product specification. For special requirements, the relevant marking work should be done according to the regulations (such as Shanghai Ziquan product port). The rate of less than or greater than 25% requires the number of interface products on each board product).

Slitting Rewinding Machineing

Domestic cutting machine development status and outlets ---

 

5. Strategically lacking deeper cooperation with film-making companies
China has made tremendous changes in the economy in the past decade or so. Film-making enterprises have grown from scratch, from large to strong, and film-making enterprises have been listed on domestic and overseas stock markets, with dozens of them, and the key slitting machine industry is currently facing The small scale and low output value are extremely disproportionate to the scale of the film-making industry. There are two reasons for the above phenomenon: First, for the manufacturing of slitting machine enterprises, the opportunity has not been seized in time, and The knowledgeable film-making enterprises have jointly developed the domestic and foreign slitting machine market. Secondly, from the perspective of film-making enterprises, they have not been able to support some cutting-edge machine enterprises with promising prospects from reducing manufacturing costs, and jointly research and develop production slitting. device. If the film-making enterprises can reduce the purchase cost and operating cost, the price competition faced by today's film-making enterprises will be alleviated, and at the same time, the world-class cutting machine enterprises will be created.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com