Plastic Bush Core Holder For Bopp Slitting Machine

Plastic Bush Core Holder For Bopp Slitting Machine

Slitting machine operating procedures -

Second, the volume of the replacement of the finished product (operating station)
1. Press and hold the “winding side 1 swing” and “winding side 2 swing” buttons until the finished roll leaves the press roller (winding arm vertical state). 2. At the same time, the blades cut off the finished product on both sides, and the end of the film is glued to the finished roll as the end mark of the finished roll. 3. Continue to press and hold the “winding side 1 swing” and “winding side 2 swing” buttons, and the winding arm will open to both sides until the finished product rolls over to the unloading trolley tray and release the button.
4. Press the “Release side 1 card head release” and “Rewind side 2 card head release” buttons, the card head will open, release the finished product roll (if the finished product roll does not come down, manually shake the finished product roll).
5. Press and hold the “winding side 1 swinging” and “winding side 2 swinging” keys, and the winding arm station will be turned up and forward until the winding arm reaches the paper discharge core position and release the button.

6. Unload and unwind the trolley and advance the finished product to the packaging area.
7. After the winding arm is in the correct position, manually install the empty paper core (the double-sided adhesive should be attached to the paper core).

Plastic Bush Core Holder For Bopp Slitting Machine

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

two. Wrinkle (wrinkle, vertical wrinkle, cross wrinkle, line wrinkle)

Through many years, the BOPP industry has carried out a series of intensive and meticulous work on solving the problem of wrinkling. From the two aspects of process parameter screening and equipment adjustment and transformation, we have found a set of effective solutions and received very good results. effect,
Methods include:

5 Under the same parameters, the long gauge is more likely to wrinkle than the short gauge film roll, which means that the longer the specification, the worse the exhaust effect, and the lower the strength of the long gauge paper tube, the slitting process paper The slight bending of the tube tends to cause the film in the middle of the film roll to wrinkle for a long time, and when the paper core is long, under the high-speed rotation of the slit, as the axis of the film winding, its straightness, concentricity, strength, The indicators such as surface finish are the most important. Generally speaking, the longer the paper core, the more difficult it is to ensure the straightness and concentricity. Therefore, the quality of the paper core is very important. It is necessary to improve the inspection of the paper core. If the paper tube is found during the slitting process, the paper tube is found. The quality is abnormal and needs to be replaced in time. In addition, under the same parameter conditions, the short gauge is more prone to deviation than the long gauge membrane coil, and a large winding pressure is required. Therefore, for the adjustment of the wrinkle, the wrinkle can be reduced by appropriately reducing the pressure setting for the long specification, and the pressure is increased for the short specification to prevent the deviation;
6 Different thickness films have different degrees of wrinkling, thick film stiffness is better, less wrinkles, thin film is more open, so the thin film should be adjusted to increase the strength of the parameters to overcome For the generation of wrinkles, different thickness of the film should have different special data for slitting;
7 The product that is slit inside and outside the slitting machine may have different degrees of wrinkling due to the different angles (wrap angles) entering the winding roller. The difference between the inner and outer wrinkles of each slitting machine should be compared, such as The difference is obvious. During the slitting process, the specification that is prone to wrinkle should be cut on the side that is not prone to wrinkle;
8 The wrinkle reduction can also be achieved by adjusting the venting performance of the pressure roller and improving the stability of the winding arm.

Plastic Bush Core Holder For Bopp Slitting Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

three. Irregular end faces
The end face irregularity refers to the unevenness of the end face which occurs when the film width is constant. The end face is generally in two forms: one is that the end faces are irregularly jagged, and the other is a regular wave-shaped irregularity.
1. Causes and countermeasures for uneven end faces:
1 The cutting parameters are not well adjusted. For example, if the cutting speed and the sheet/pressure are poorly matched, the sheet/pressure curve should be set according to the slitting speed;
2 abnormal vibration of the cutting device, overhaul;
3 divided and unwinding rolls are unbalanced and adjusted;
4 The parameters of the winding arms at both ends are inconsistent, and the force distribution of the winding process affects the flatness of the end face, usually the wavy end faces are not aligned and overhauled;
5 The influence of film properties, such as smoothness, etc., Ts, Pm and other models are more prominent, and the cutting parameters should be set according to different film characteristics;
6 film thickness is uneven;
7 Wrinkling during the slitting process will also cause unevenness of the end face and adjust the flattening film;
8 If the film is too static, improve the electrostatic properties of the film or check if the static eliminator of the slitter is invalid.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com