Double Sided Reflective Adhesive Tape Slitting Rewinding Machine

Double Sided Reflective Adhesive Tape Slitting Rewinding Machine

Slitting machine operating procedures -

Second, the volume of the replacement of the finished product (operating station)
1. Press and hold the “winding side 1 swing” and “winding side 2 swing” buttons until the finished roll leaves the press roller (winding arm vertical state). 2. At the same time, the blades cut off the finished product on both sides, and the end of the film is glued to the finished roll as the end mark of the finished roll. 3. Continue to press and hold the “winding side 1 swing” and “winding side 2 swing” buttons, and the winding arm will open to both sides until the finished product rolls over to the unloading trolley tray and release the button.
4. Press the “Release side 1 card head release” and “Rewind side 2 card head release” buttons, the card head will open, release the finished product roll (if the finished product roll does not come down, manually shake the finished product roll).
5. Press and hold the “winding side 1 swinging” and “winding side 2 swinging” keys, and the winding arm station will be turned up and forward until the winding arm reaches the paper discharge core position and release the button.

6. Unload and unwind the trolley and advance the finished product to the packaging area.
7. After the winding arm is in the correct position, manually install the empty paper core (the double-sided adhesive should be attached to the paper core).

Double Sided Reflective Adhesive Tape Slitting Rewinding Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

 

thirteen. Foreign matter such as dust and small flying insects in the film roll

In addition, paper-end paper dust contamination, contamination of the film roll by the operator and the packaging staff, uneven size of the paper tube, label identification (length, weight, etc.), bumps, poor packaging, etc. are also easy to cut. For quality problems, we must pay attention to every detail during the operation and packaging process. For example, before the slitting machine starts, the film should be neatly placed and attached to the paper tube. The film should not exceed the end of the paper tube. Pay attention to the hands of the operator. Neat and clean environment of the cutting place, the packaging and handling process should be handled with care. When the film roll is moved down the manual forklift, pay attention to the stability, do not hit the film surface, the sealing box of the packaging process, the sticker cap, the sticker The labeling and labeling should be carried out in strict accordance with the specified requirements, position and size. It is not free to ensure the quality of the film products from every link.

Double Sided Reflective Adhesive Tape Slitting Rewinding Machine

Domestic cutting machine development status and outlets ---

1. Not rigorous in the manufacturing process
Tolerance control in the mechanical manufacturing process is not precise enough, and the surface is rough, especially in the matching electroplating industry, which is shoddy. There is a defect in the dynamic balance of the roller for cutting the Chinese-made equipment at one time. The lag of the related industry, the rubber coated by the roller has far less wear resistance and anti-aging than the foreign products. The bearings used seem to use well-known foreign brands, but the counterfeit and shoddy floods the domestic bearing market. Even when the real goods are purchased, the precision is far lower than the precision used by foreign slitting machines.
In the entire production process of a slitting machine, there is no guarantee of production process. At present, most of the slitting machines produced in China are completed by a number of outsourcing units, and the quality of their production is even more difficult to guarantee. In addition, the metal materials used and the heat treatment process are not rigorous enough, resulting in many problems in the use of a slitting machine. It has seriously affected the share of a slitting machine in the domestic market. The secondary and tertiary slitting machines have fewer problems than the one slitting machine, because the parts of the secondary and tertiary slitting machines are completed by the slitting machine manufacturer, and the dynamic balancing machine used is in a narrow range. It can accurately control the unbalanced grams, and the industrial difficulty coefficient of manufacturing is reduced. Its selling price is far lower than that of foreign products. Therefore, the proportion of domestically produced slitting machines in the domestic slitting machine market getting bigger.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com