Kraft Paper Tape Slitter Machine

Kraft Paper Tape Slitter Machine

Slitting machine operating procedures -

Second, the volume of the replacement of the finished product (operating station)

8. Operate the button on the winding arm to wind up the paper core.
9. Manually cut the film to be cut onto the corresponding rewinding paper core. After tightening the film, it is firmly adhered to the paper core (note that the side 1 and side 2 films are differently worn).
10. After all the paper cores on both sides are glued, press “Crop 1 Clamp” and “Reel 2 Clamp” at the same time, and then press “Rewind side 1 open” and “winding side 2 open” at the same time. The position is automatically swung until the winding paper core is pressed against the upper roller, the winding main body is started, and the film is slowly wound until it is tight. (The two-button white indicator light turns from blinking to steady light)
11. Press the “MACHINE” button, the siren will sound and the signal light will flash yellow. Confirm that the personnel are in the safe area, press "machine on" again, the button light is always on, the machine starts and accelerates to the input set speed.

12. The main operator shall check the winding condition of each film and fine-tune the winding arm if necessary.

Kraft Paper Tape Slitter Machine

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

(3) Causes of loose/overtightening of the film roll
1. The influence of the cutting parameters (winding sheet / pressure curve setting factors, etc.);
2. Effect of film properties (stiffness, thickness, single/double corona surface, smoothness, static electricity, etc.)
Ringing, the slitting parameters must be set according to the film with different characteristics);
3. The effect of the winding speed (when the winding speed is slower, the more time the slitting process is to discharge the air in the film roll, the tighter the film winding is);
4. Product specifications (width, length, collocation, etc.);
5. The influence of the performance of the slitting equipment (adjustability, stability, operability, etc.);
6. The influence of operational factors (professional level, operational skills, job responsibility, etc., generally expressed in the insertion
7. The quality of the work is wrong, such as poor air-suction, rewinding card head position, poor adjustment, and unwinding roller pressure; The influence of environmental factors (temperature, humidity, etc.);
8. Influencing factors of the appraisal system (Operator considers the appraisal of the secondary processing and rewinding indicators in the workshop, and often adopts the coping method of winding up and not loosening, which is one of the factors that cause the film roll to be over-tightened);

Kraft Paper Tape Slitter Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

Seven. Sharp edge
The curling occurs at the edge of the film winding, which causes the curling. The reason is that the edge of the thick film is curled up and the edge part is lifted up; the second is that the winding is too tight, and the tension can be shortened by slitting. Speed ??to improve the resulting edge curling phenomenon; third, the cutter is too blunt, and the stretching phenomenon occurs at the slit when slitting, causing the edge of the film roll to be turned outwards after winding to cause the curling edge, and the cutting should be replaced in time. The knife can avoid the occurrence of the curling problem; the fourth is that the tool is not installed correctly, such as the blade is close to the edge of the sipe and the blade is passivated. Cutting with a round knife can improve the curling of the film roll.
In the use of the unwinding process, there will be different degrees of side-floating in the unwinding process, and it is impossible to track the alignment with the electric eye, which directly affects the use effect. Therefore, it is necessary to change the product with the curled edge.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com