Pvc Adhesive Tape Automatic Slitting Machine

Pvc Adhesive Tape Automatic Slitting Machine

Slitting machine operating procedures -

Second, the volume of the replacement of the finished product (operating station)

8. Operate the button on the winding arm to wind up the paper core.
9. Manually cut the film to be cut onto the corresponding rewinding paper core. After tightening the film, it is firmly adhered to the paper core (note that the side 1 and side 2 films are differently worn).
10. After all the paper cores on both sides are glued, press “Crop 1 Clamp” and “Reel 2 Clamp” at the same time, and then press “Rewind side 1 open” and “winding side 2 open” at the same time. The position is automatically swung until the winding paper core is pressed against the upper roller, the winding main body is started, and the film is slowly wound until it is tight. (The two-button white indicator light turns from blinking to steady light)
11. Press the “MACHINE” button, the siren will sound and the signal light will flash yellow. Confirm that the personnel are in the safe area, press "machine on" again, the button light is always on, the machine starts and accelerates to the input set speed.

12. The main operator shall check the winding condition of each film and fine-tune the winding arm if necessary.

Pvc Adhesive Tape Automatic Slitting Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

twelve. Interface quality problem (poor interface quality, interface identifier does not match)

2. Interface identifier
Due to the large thickness of the film interface, the film roll for some applications must be properly handled at the interface to avoid unnecessary problems, such as slowing down, increasing the gap between the coating blade, and printing the offset plate. The interface products must be identified as necessary to facilitate customer identification and internal management.
1 The color of the adhesive interface is generally beige, special requirements are used according to the regulations. For example, Shanghai Ziquan requires the use of black adhesive tape; the marking method of the joint position is operated according to the regulations, such as Zhuhai Zhongfu Pearl Film, Shenzhen Ruimei The hot film is required to be marked at the ends of the interface with yellow paper dust protruding from the end of the film roll by about 1 cm; other special marks are operated according to the requirements of the production tribe.
2 Require the slitting workshop to mark the length number of the joint product without special requirements after the length of the label in the length column of the package label, and mark the “buter” mark on the note bar of the computer, and mark “+” on the remark column. Marking, pearl film and imitation paper film and exporting pearl film should indicate the length of each product before and after the joint on the length column of the product specification. For special requirements, the relevant marking work should be done according to the regulations (such as Shanghai Ziquan product port). The rate of less than or greater than 25% requires the number of interface products on each board product).

Pvc Adhesive Tape Automatic Slitting Machine

Domestic cutting machine development status and outlets ---

3. Lack of insight into the characteristics of different materials at the time of slitting, distinguishing between control systems and structures
Everyone knows that the physical properties of different materials are inconsistent. Some materials are smooth and firm. Some materials are very soft and soft, and the physical properties of the same material with different thicknesses are not the same. Among the slitting machines, the structure is also different, and there is a lack of changes in the control system due to its structural changes. The difference is rarely studied. In particular, the change in the difference in the control curve is even less known, and its mature control system software is still very few in China. Although some people have tried the application of a slitter control software, the chances of success are very low. Most of them are characterized by “headaches and pains.” Although our company has experienced 7-8 years of hard work, Some experience has been gained and the control system is becoming more mature, but there is still a certain gap compared with the materials covered by well-known foreign brands.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com