Automatic Machinery Bopp Tape Slitting Rewinding Machine

Automatic Machinery Bopp Tape Slitting Rewinding Machine

Slitting machine operating procedures -

Second, the volume of the replacement of the finished product (operating station)

8. Operate the button on the winding arm to wind up the paper core.
9. Manually cut the film to be cut onto the corresponding rewinding paper core. After tightening the film, it is firmly adhered to the paper core (note that the side 1 and side 2 films are differently worn).
10. After all the paper cores on both sides are glued, press “Crop 1 Clamp” and “Reel 2 Clamp” at the same time, and then press “Rewind side 1 open” and “winding side 2 open” at the same time. The position is automatically swung until the winding paper core is pressed against the upper roller, the winding main body is started, and the film is slowly wound until it is tight. (The two-button white indicator light turns from blinking to steady light)
11. Press the “MACHINE” button, the siren will sound and the signal light will flash yellow. Confirm that the personnel are in the safe area, press "machine on" again, the button light is always on, the machine starts and accelerates to the input set speed.

12. The main operator shall check the winding condition of each film and fine-tune the winding arm if necessary.

Automatic Machinery Bopp Tape Slitting Rewinding Machine

Slitting machine operation guide ---

3 job responsibilities
3.1 Slicing machine gear duties
3.1.1 Conscientiously abide by the rules and regulations of the company and the production department, and obey the leadership with the monitor.
3.1.2 Proper operation and use of equipment, strict compliance with safe operating procedures, and timely elimination of common faults.
3.1.3 According to the requirements of product quality standards, it is responsible for the quality, consumption, safety and task completion of the machine, and self-inspection and its records.
3.1.4 Responsible for guiding, supervising and managing the work of the machine personnel.
3.1.5 According to the maintenance requirements of the equipment, carefully carry out the maintenance work of the equipment.
3.1.6 Work with the machine personnel to do a good job of cleaning the equipment and the area of ??responsibility.
3.1.7 Carefully carry out the work of handover, and communicate and record the problems existing in the operation of the equipment.
3.1.8 Have the responsibility for care and maintenance of the auxiliary facilities (lighting, emergency lights, tables, chairs, shelves, etc.) belonging to the machine and surrounding.
3.1.9 Complete the other tasks assigned to the squad leader and the superior leader.
3.2 Slitting machine auxiliary duties
3.2.1 Conscientiously abide by the rules and regulations of the company and the production department, obey the management of the vehicle, and strictly abide by the safe operating procedures.
3.2.2 Carefully assist the gear shifter to adjust and troubleshoot the equipment, and timely carry out the sanitary cleaning work within the scope of the equipment responsibility area under its jurisdiction.
3.2.3 Do a good job in preparation before starting the machine, do a good job in paper and product handling, and do a good job in quality self-inspection.
3.2.4 Clean up waste paper, garbage, packaging materials and evacuate the production site in time; cut off the power and air supply of the machine and auxiliary facilities at the end of the work.
3.2.5 Receive raw and auxiliary materials according to the requirements of the gears and do the work and identification of the original and auxiliary materials.
 

Automatic Machinery Bopp Tape Slitting Rewinding Machine

Slitting machine operation guide ---

6 Safety Precautions
6.1 The operator must be trained to work and wear the labor protection products correctly; carefully check the protective devices, safety interlocks, test buttons, emergency buttons, etc. of the machine before starting the machine, and confirm that the machine can be turned on after normal operation.
6.2 The slitting machine is a double-operated equipment. It is forbidden to operate in tandem, especially when the equipment is repaired.
6.3 The cut products should be stacked neatly and securely, and fixed with a cannula to prevent the product from slipping and hurting people.
6.4 When working, it is not allowed to place any irrelevant items such as oil pots and tools on the workbench.
6.5 During the operation of the machine, it is strictly forbidden to reach into the circumference of the slitting knife or the pressure roller. Even if the vehicle has been stopped but the power is not disconnected, it is forbidden to perform the tool change, paper adjustment and adjustment under the knife.
6.6 Slitting blades must be protected during handling and storage, and must not be handled or stored with bare edges.
6.7 The interlocking protection devices of all parts of the equipment shall not be short-circuited or removed, and if malfunction or abnormality occurs, stop immediately and report to the machine for repair and maintenance.
6.8 Machine personnel shall not perform fault repair or equipment adjustment of fault type, and the power distribution cabinet, switch box, etc. shall not be opened without authorization, and shall not store items.
6.9 When handing over the shift, you must hand over the site, and you must explain the production and equipment operation of the class to the next one.
6.10 Check the surrounding conditions before leaving work, and cut off the power and air supply of the machine and related equipment.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com