Automatic Machinery Bopp Opp Tape Slitting Rewinder Machine

Automatic Machinery Bopp Opp Tape Slitting Rewinder Machine

Slitting machine operating procedures -

Third, through the film:
1. The cutter exits to the stop position. (The split knife switch is in the off position)
2. Press the “Pinch with chain” button and the hook and loop on the chain will run to the feeding position.
3. Press “Release Brake” until the indicator light is on, and the unwinder brake is released.
4. Pull one end of the film manually, pull the film along the running route to the film-piercing mechanism, and fix the film to the shackle of the chain.

Automatic Machinery Bopp Opp Tape Slitting Rewinder Machine

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

two. Wrinkle (wrinkle, vertical wrinkle, cross wrinkle, line wrinkle)

Through many years, the BOPP industry has carried out a series of intensive and meticulous work on solving the problem of wrinkling. From the two aspects of process parameter screening and equipment adjustment and transformation, we have found a set of effective solutions and received very good results. effect,
Methods include:
1 The wrinkles near the core of the paper can not be stretched, which is largely related to the contact roller pressure of the slitter. It has been proved that when the contact roller pressure is increased, the wrinkles increase, and when the pressure is reduced, the wrinkles are reduced, and the air inside the film roll is reduced. The amount is increased, so that the gap between the membranes is increased to reduce friction, which is beneficial to reduce wrinkles;
2 When the winding pressure is small, the wrinkle is less, but the small pressure will cause the film roll to run off. Therefore, it is very important to set the pressure curve reasonably. When starting, set a small pressure, when it is easy to wrinkle. After a length of time has passed, the pressure should be increased rapidly to avoid the occurrence of deviation;
3 In the improvement of wrinkle, the control of winding tension should be considered. If only the winding pressure is considered, the initial pressure setting value will be very small. In case of special circumstances, the deceleration will cause deviation due to small pressure. Defects, so the tension curve setting is also very important, and the winding pressure and tension must be matched properly.
4 The pressure at the core of the paper cannot be reduced indefinitely. If it is too small, the inside of the film roll will be too loose, and the end face will appear star-shaped, causing the film to wrinkle. Therefore, it should be adjusted to the film roll when setting the pressure curve. The end face has neither a star shape and minimizes wrinkles;

Automatic Machinery Bopp Opp Tape Slitting Rewinder Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

four. Deviation
Deviation refers to the phenomenon that part of the film on the end face of the film roll is misaligned, which is caused by the sliding of the film during the winding process.

2. Causes and countermeasures of deviation:
(1) The problem of the quality of the slitting in the same category as the deviation of the end face is, in terms of degree, the degree of misalignment is more serious than the misalignment of the end face; in terms of nature, the general end face is not a continuous problem. However, the deviation is mostly an accidental problem; from the analysis of the reasons, the cause of the unevenness of the end face may cause the occurrence of the deviation problem.
(2) Since the deviation of the deviation from the end face is more prominent, the eye point should be placed in the fine point when the end face is not aligned. When analyzing the deviation problem, the eye point should be widened, especially the factor of the cutting speed. The effect is that the acceleration and deceleration are too rapid. For a film with good smoothness, it is easy to cause slippage and cause a split layer, and the slitting speed should be slowed down.
(3) For products with narrow slitting, too tight winding of the film roll will cause the film to slip laterally. If the film roll is too loose, air will be trapped, which will cause the film roll end to be staggered. Roll tension.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com