Automatic Rewinding And Slitting Machine

Automatic Rewinding And Slitting Machine

Slitting machine operating procedures -

Third, through the film:
1. The cutter exits to the stop position. (The split knife switch is in the off position)
2. Press the “Pinch with chain” button and the hook and loop on the chain will run to the feeding position.
3. Press “Release Brake” until the indicator light is on, and the unwinder brake is released.
4. Pull one end of the film manually, pull the film along the running route to the film-piercing mechanism, and fix the film to the shackle of the chain.

Automatic Rewinding And Slitting Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---
two. Wrinkles (wrinkles, vertical wrinkles, cross wrinkles, wrinkles)

 

(2) Causes and countermeasures of longitudinal wrinkles
Longitudinal wrinkles mean that the surface of the film roll forms a circumferential rib line. In the process of slitting, a large amount of air entrapment or cumulative thickness unevenness is the main cause of longitudinal streaks, and it is difficult to eliminate the occurrence of a relatively serious stripe. When the longitudinal wrinkles appear in the slitting process, the tension is reduced and the pressure is applied to discharge the air in the film roll to improve the longitudinal wrinkle problem. However, the adjustment range should consider the impact on wrinkles and other aspects (according to relevant professional information, longitudinal wrinkles One of the reasons is that the slitting speed is too fast, and the film roll is most prone to the quality problem of the longitudinal stripe at high speed, but there is no obvious influence in actual production, which remains to be studied). Another reason for the vertical wrinkles is the influence of the running accuracy of the equipment. For equipment with high requirements for running accuracy, after a long period of continuous use, the running accuracy of some components has decreased. For large slitting machines, it is more difficult to ensure the running accuracy due to the large number of running parts. Moreover, since the plastic film is a polymer product, its thickness is very thin, and it is more susceptible to damage during processing. Therefore, once the running accuracy is insufficient, quality problems such as vertical streaks are likely to occur. For this reason, it should be cautious when replacing equipment parts and accessories. It is advisable to use durable and high-precision parts, and it must also ensure a certain precision during installation. Otherwise, it is difficult to meet the operation requirements of the slitting machine.
The flattening roller flattens the film and eliminates some of the longitudinal wrinkles produced by the film under tensile stress.
(3) Causes and countermeasures of cross wrinkles
In addition to the influence of the parent-rolling factor, the transverse wrinkles of the film are mainly caused by the sag-like transverse wrinkles produced by the loosening of the slit film roll. Generally, the slitting process is effective in reducing the wrinkles and reducing the pressure, and should be effective for different types of products. Adjusting the slitting and pressure can effectively eliminate the occurrence of cross wrinkles.

Automatic Rewinding And Slitting Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

three. Irregular end faces
The end face irregularity refers to the unevenness of the end face which occurs when the film width is constant. The end face is generally in two forms: one is that the end faces are irregularly jagged, and the other is a regular wave-shaped irregularity.
1. Causes and countermeasures for uneven end faces:
1 The cutting parameters are not well adjusted. For example, if the cutting speed and the sheet/pressure are poorly matched, the sheet/pressure curve should be set according to the slitting speed;
2 abnormal vibration of the cutting device, overhaul;
3 divided and unwinding rolls are unbalanced and adjusted;
4 The parameters of the winding arms at both ends are inconsistent, and the force distribution of the winding process affects the flatness of the end face, usually the wavy end faces are not aligned and overhauled;
5 The influence of film properties, such as smoothness, etc., Ts, Pm and other models are more prominent, and the cutting parameters should be set according to different film characteristics;
6 film thickness is uneven;
7 Wrinkling during the slitting process will also cause unevenness of the end face and adjust the flattening film;
8 If the film is too static, improve the electrostatic properties of the film or check if the static eliminator of the slitter is invalid.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com