Fully Automatic Self Adhesive Bopp Jumbo Rolls Slitting Rewinding Machine

Fully Automatic Self Adhesive Bopp Jumbo Rolls Slitting Rewinding Machine

Slitting machine operating procedures -

Third, through the film:

14. Press the “MACHINE” button, the siren will sound and the signal light will flash yellow. Confirm that the personnel are in the safe area, press "machine on" again, the button light is always on, the machine starts and accelerates to the input set speed.
15. If necessary, perform parent roll adjustment, brake tension adjustment, and flattening roller position check at low speed.

Fully Automatic Self Adhesive Bopp Jumbo Rolls Slitting Rewinding Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

eleven. Width deviation is too large
     The width of the film roll is limited by the gap of the sipe roll. The actual slit width will deviate from the width required for the order, but the deviation should be controlled within the tolerance range of ±2mm required by the national standard. The so-called width deviation Large, that is, the actual width of the film roll exceeds the requirements of internal control standards or customer standards.
     Not all products have a tolerance of ±2mm, and some customers can only take deviations from the film width, such as the Pd film of Kunshan Zhangpu, the LL film of Shanghai Zhicheng, the PL film of Beijing Amcor, etc. It is required to adjust the film width.

Fully Automatic Self Adhesive Bopp Jumbo Rolls Slitting Rewinding Machine

Slitting machine parts ---

1. Type of inspection system for the tension and speed of the slitting machine:
1 Tension sensor detection: The tension sensor is installed under the bearing of the tension detecting roller, converts the detected aluminum foil tension into an electrical signal, sends it to the tension adjuster, compares it with the original set tension signal, performs PID calculation, and then inputs The winding motor controller achieves the purpose of controlling the tension and rotation speed of the winding roller.
2Floating roller indirect tension detecting system: a set of floating roller is installed in front of the aluminum foil tracking roller. The position of the floating roller is detected by a potentiometer. The tension control method is to keep the tension constant by keeping the position of the floating roller as constant as possible. .
3 The magnetic powder clutch is used to control the rotational torque of the input winding roller to achieve tension control: the magnetic powder clutch is composed of an active part and a driven part, and is connected to the winding roller through a transmission mechanism such as a universal joint, and the fine ferromagnetic powder is filled in the middle. As a torque transmission medium. A magnetic field is formed by applying a constant current to the exciting coil, and the magnetic powder is magnetized. The magnetized magnetic powder attracts each other to form a chain arrangement. When the active part rotates at a constant speed, the coupling force between the magnetic powders is broken to form a circumferential tangential force, and the product of the tangential force and the radius of the magnetic ring is the driving driven part. The winding torque of the winding realizes the coupling of the output torque from the active part to the driven part in continuous rotation, thereby achieving the purpose of controlling the tension.
4 slitting Unwinding capacity and speed detection system: The magnetic powder tension brake is mainly used to control the unwinding force and speed. The working principle is: the coupling is installed in the magnetic powder brake, and the input parts and output with magnetic coils are installed. component. Below the magnetic coil is an annular groove, the underside of which is an annular rotor or output member. The annular groove is located at the center of the output member and is filled with magnetic powder. When there is excitation current in the magnetic coil, the coil generates magnetic flux to align the magnetic powder in the direction of the magnetic field, thus generating damping between the input member and the output member, and transmitting the torque. If the tension and speed applied to the aluminum foil are increased or decreased, the magnitude of the exciting current can be changed, or the magnitude of the current applied to the coupling coil by the varying amplifier can be effectively controlled.


Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?