Packing Tape Machine Manufacturers Bopp Tape Slitting Rewinding Machine

Packing Tape Machine Manufacturers Bopp Tape Slitting Rewinding Machine

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

(2) The purpose, method and characteristics of hardness testing
1. OBJECTIVE: The hardness test method provides a quantifiable means for determining the tightness of the film roll and provides a quantifiable basis for the determination.
Some of the product quality characteristics can be quantitative, and some can not be quantified, can only be qualitative. In the past, our judgment on the tightness of the film winding is only based on the hand feeling. The scale of the judgment is difficult to grasp, and the difference between different inspectors Larger. In actual work, when measuring, the non-quantitative characteristics are usually converted into quantifiable substitute quality characteristics, which are used as the basis for evaluation, inspection and assessment. Film roll hardness testing is a means of quantitative control of the main quality characteristics of the slitting under this guiding ideology. However, it is worth emphasizing that not all quality characteristics must be quantified, especially the film as a process material quality characteristic, there are quantitative measurement characteristics, such as thickness, tensile strength, gloss, etc., also have qualitative characteristics, only the process Subjective judgments such as wrinkles, blots, chromatic aberrations, etc.

2. Several characteristics of film roll hardness
1 Different film varieties, the hand tightness is similar but the hardness data is different. This is because the hand roll is used to squeeze the film roll in a certain area of ??the finger, which is a test of one surface, and when the hardness tester is used, it is a The pin point is pressed against the film roll, which is a detection of a point, and there will be differences between the two;
2 different film varieties have different winding hardness requirements, which are based on the characteristics and uses of various films;
3 The tightness and hardness of the film roll are not completely linear. The most sensitive value is between 87 and 95. When the hardness is as low as 85, the rewinding does not affect the hardness. Similarly, when the hardness is high. At 97 o'clock, the effect of rewinding on the film roll hardness is getting smaller and smaller.
4 Winding hardness is a reference index for quantifying the winding tightness. It only reflects a quality characteristic of the film roll surface and does not reflect the fullness of the film roll. Therefore, the key is to effectively control the film roll tightness. The quality of the product used.

Packing Tape Machine Manufacturers Bopp Tape Slitting Rewinding Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

twelve. Interface quality problem (poor interface quality, interface identifier does not match)

3. Interface length and interface rate requirements
Since the interface products will inevitably generate certain scraps before and after the interface, and the quality of the interface products cannot reach 100% of the quality level of the interfaceless products, increasing the loss of use, therefore, the film manufacturers and users are The number of interfaces of the volume product and the interface ratio of each batch of products are specified, so that the interface products are controlled within a certain range.

Packing Tape Machine Manufacturers Bopp Tape Slitting Rewinding Machine

Domestic cutting machine development status and outlets ---

three. Domestic slitting machine development direction
The development direction of domestic slitting machines should be considered from three aspects:

2. Automation control part: At present, the automation level of the slitting machine produced in China is still at the middle and lower level. Although the domestic control of the original device has been widely used and the price is lower, the domestic slitter manufacturers are far away in use. It lags behind the level of developed countries, especially in the control system, and the lack of organic combination with the structure of the slitting machine and the material to be cut. At this level, most of the domestic slitting machines still stay on the thick lines. The rigor and rationality of the cutting machine control system has not been fully understood. I personally think that the domestic slitting machine manufacturers should start from the above several directions, and find out the method that meets the cutting and cutting principle of the slitting machine and can maximize the use of the functions provided by the hardware.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com