Automatic Paper Coating Machine

Automatic Paper Coating Machine

1. Moveable blade device. 
2. Guiding roller in oven will synchronously rotates with main shaft. 
3. Solenoid operated valve controlling is adopted for Anilx roller and drawing roller. 
4. Automatic meter-measuring devices. 
5. Key mode air shaft is used for unwinding and rewinding shafts, easy to load and unload. 

Automatic Paper Coating Machine

Second, the length of the coating section changes, the spacing is unstable:

6. When the back roller and the coating roller are in contact with each other, the gap between the two ends is inconsistent and the pole piece is wrinkled. Regardless of whether the first side or the second side is applied, the gap should be carefully adjusted. First, the gap is appropriately enlarged, and then slowly reduced. At the same time, observe the dial scale of the coating roller just touching the foil strip, and then Reduce the gap by 0.03mm.
7. When the correction system is abnormal, the pole piece will be wrinkled. Check the three correction systems before and after the inspection, whether it is in the automatic state. If the lengths of the foil strips are inconsistent, that is, when the file is bent too much, the pole pieces will be wrinkled. Exceeding the correcting ability, the foil has to be replaced. 8. When the pole piece tension is too large, the pole piece is wrinkled. Check that the tension setting is reasonable. Then check each drive roller. The rotation of the take-up roll is flexible. Handle inflexible rollers in time.
9. When the back roller is in the inconsistent stroke, the pole piece is wrinkled. It is necessary for the mechanic to check. Confirm and adjust. After the back roller and the coating roller are pulled apart, the gap between the two sides is 1mm (see the dial indicator), and the test is started. When the tail is qualified, lock the nut.

10. The surface of the rubber roller on the back roller will undergo periodic elastic deformation during re-use. When a certain degree of deformation remains, wrinkles will occur. At this time, new products must be replaced.
11. The cause of looseness of a certain roller fastening screw causes the parallel state of each roller to be destroyed, and wrinkles may occur at this time. As long as it is found in time to adjust and tighten in time.

Automatic Paper Coating Machine

PET film--

 

(7) PET shrink film
Polyester heat shrinkable film is a new type of heat shrinkable packaging material. Due to its easy recycling, non-toxicity, odorlessness, good mechanical properties, and especially environmental protection, polyester (PET) has become an ideal substitute for polyvinyl chloride (PVC) heat shrinkable film.
However, the ordinary polyester is a crystalline high polymer, and the ordinary PET film can only obtain a heat shrinkage rate of 30% or less by a special process. To obtain a polyester film with a higher heat shrinkage rate, it must also be modified. That is, in order to prepare a polyester film having a high heat shrinkage ratio, it is necessary to copolymerize a common polyester, that is, polyethylene terephthalate. The copolymerized modified PET film has a maximum heat shrinkage rate of more than 70%.
The characteristics of the heat-shrinkable polyester film: it is stable at normal temperature, shrinks upon heating (above the glass transition temperature), and is more than 70% heat shrinkage in one direction. The advantages of heat shrinkable polyester film packaging are:
1 The body is transparent, reflecting the image of the product.
2 tightly packed with good anti-scattering properties.
3 rain, moisture, mildew.
4 no recovery, there is a certain anti-counterfeiting function. Heat shrinkable polyester film is often used in the convenience food, beverage market, electronic appliances, metal products, especially shrinkage labels are its main application areas. Because with the rapid development of PET beverage bottles, beverage bottles such as cola, sprite, and various juices need PET heat shrinkable film to be used as a heat seal label. They are all polyester-based, environmentally friendly materials, and easy to recycle. use.
In addition to being used as a shrink label, heat-shrinkable polyester film has also been used in outer packaging for daily use products in recent years. Because it can protect the packaged goods from impact, rain, moisture, rust, and the product can win the user with a beautifully printed outer packaging, and it can show the good image of the manufacturer. At present, more and more packaging manufacturers use printed shrink film to replace traditional transparent film. Because the printing shrink film can improve the appearance of the product, which is conducive to the advertising of the product, the trademark brand can make a deep impression on the consumer.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com