Skotch Tape Slitter Rewinder

Skotch Tape Slitter Rewinder

Introduction to slitting machine:
     Slitting machine is a kind of mechanical equipment for slitting wide sheets of paper or film into a plurality of narrow-width materials, which are commonly used in papermaking machinery and printing and packaging machinery.
     The traditional control scheme of the slitter is to use a large motor to drive the shaft of the rewinding and unwinding. A magnetic powder clutch is added to the reel and reel, and the resistance generated by the magnetic clutch is controlled to control the tension of the surface of the material. . Magnetic powder clutches and brakes are special automatic actuators that transmit torque through the magnetic powder filled in the working gap. The magnetic current can be changed to change the magnetic state of the magnetic powder, and then the transmitted torque can be adjusted. It can be used for stepless speed regulation from zero to synchronous speed. It is suitable for high speed section fine adjustment and medium and small power speed control system. It is also used to adjust the torque by adjusting the current to ensure an unwinding or rewinding tension control system with a constant tension during winding.

Skotch Tape Slitter Rewinder

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

(2) The purpose, method and characteristics of hardness testing

 

3. Method for detecting film roll hardness
1 selection of testing equipment
There are various instruments for detecting the hardness of an object, but so far there has not been a hardness tester that professionally detects the hardness of a film roll. Due to the large difference in surface hardness between various objects and the variety of hardness testers, it is important to select a hardness tester that can effectively reflect the tightness of the film roll. After screening and comparison, our company has determined the "A-type rubber hardness tester" for detecting the surface hardness of rubber products as an auxiliary instrument for detecting the tightness of the film roll.
2 detection instrument correction
Since the "A type rubber hardness tester" is not a special test instrument for the film roll, in order to improve the detection accuracy of the instrument, we have modified the structure of the hardness tester according to the characteristics of the film, and increased the presser area by 5 times.
3 detection methods a.
Before the test, the pointer of the hardness tester should be in the free state and point to the zero position. When pressing the hardness tester on the glass plate, the pointer should be 100 degrees (the end face of the press pin and the bottom of the foot are in close contact with the glass). If the zero position and the 100 degree are not indicated, the needle can be pressed slightly several times, if not When referring to zero and 100 degrees, it cannot be used. The hardness tester to be confirmed can be used again if it meets the requirements for use. b.
When testing the hardness, put the hardness tester on the side of the film product, take the left, middle and right positions, at least 40mm from the edge of the film roll, and firmly press the end of the hardness tester with both hands, so that the pressure pin is pressed vertically. The sample is read within 1 s until the pressure is fully contacted with the sample, and the average is taken and recorded.

Skotch Tape Slitter Rewinder

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

(3) Causes of loose/overtightening of the film roll
1. The influence of the cutting parameters (winding sheet / pressure curve setting factors, etc.);
2. Effect of film properties (stiffness, thickness, single/double corona surface, smoothness, static electricity, etc.)
Ringing, the slitting parameters must be set according to the film with different characteristics);
3. The effect of the winding speed (when the winding speed is slower, the more time the slitting process is to discharge the air in the film roll, the tighter the film winding is);
4. Product specifications (width, length, collocation, etc.);
5. The influence of the performance of the slitting equipment (adjustability, stability, operability, etc.);
6. The influence of operational factors (professional level, operational skills, job responsibility, etc., generally expressed in the insertion
7. The quality of the work is wrong, such as poor air-suction, rewinding card head position, poor adjustment, and unwinding roller pressure; The influence of environmental factors (temperature, humidity, etc.);
8. Influencing factors of the appraisal system (Operator considers the appraisal of the secondary processing and rewinding indicators in the workshop, and often adopts the coping method of winding up and not loosening, which is one of the factors that cause the film roll to be over-tightened);

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com