Simple Bopp Tape Slitting Rewindng Machine

Simple Bopp Tape Slitting Rewindng Machine

Introduction to slitting machine:
     Slitting machine is a kind of mechanical equipment for slitting wide sheets of paper or film into a plurality of narrow-width materials, which are commonly used in papermaking machinery and printing and packaging machinery.
     The traditional control scheme of the slitter is to use a large motor to drive the shaft of the rewinding and unwinding. A magnetic powder clutch is added to the reel and reel, and the resistance generated by the magnetic clutch is controlled to control the tension of the surface of the material. . Magnetic powder clutches and brakes are special automatic actuators that transmit torque through the magnetic powder filled in the working gap. The magnetic current can be changed to change the magnetic state of the magnetic powder, and then the transmitted torque can be adjusted. It can be used for stepless speed regulation from zero to synchronous speed. It is suitable for high speed section fine adjustment and medium and small power speed control system. It is also used to adjust the torque by adjusting the current to ensure an unwinding or rewinding tension control system with a constant tension during winding.

Simple Bopp Tape Slitting Rewindng Machine

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

(iv) Effect of film roll tightness on product quality

(5) Coping methods
1. Reasonable principle: Applicable is reasonable, which means that the cutting operator and the quality inspector are too loose according to the winding/
Too tightly influence the degree of influence on different products, adjust the cutting process reasonably, and reasonably grasp the tightness of the film roll to meet the requirements of the use of film products.
2. Ningsong Motight principle: objective when cutting equipment status, product specifications, film performance characteristics, etc.
When the influence of the condition causes the winding tightness to be in an inappropriate degree, the principle of tightness is generally used, because the problem of over-tightening often makes the film unusable, except for the special requirements.
3. The principle of primary and secondary: it means that in the process of slitting production, small groups should be followed to the interests of large collectives.
The principle of benefiting the interests of the company, avoiding the pursuit of high output and high distribution for the purpose of reducing the quality of cutting, all should be based on product quality, maintaining the German crown film brand as the responsibility, effectively completing various production and quality indicators Effectively serve the enterprise and users, and strive to be the best supplier of film.
4. System Management Principles: Refers to the use of systematic, scientific management methods, practical, theoretical, and empirical
The accumulated cutting control method is compiled, and according to the optimal combination of different types of products, width, winding length, season and other external variables and slitting tension, pressure and other internal variables, the document control management is performed to form an operation guidance document. Minimize the influence of subjective factors, reduce the impact caused by insufficient individual ability or excessive dependence on experience, and continuously supplement, optimize and improve the operation guidance documents to meet the needs of system management.

Simple Bopp Tape Slitting Rewindng Machine

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

two. Wrinkle (wrinkle, vertical wrinkle, cross wrinkle, line wrinkle)
1. The effect of wrinkles on the quality of use
BOPP film is commonly known as "cellophane", which reflects the film's high stiffness, high transparency and good gloss. The film is wrinkled, which means that the flatness of the film is damaged to a certain extent. This is not allowed for any film. Not only will it affect the appearance of deep-processed products, but also cause quality defects in use, such as lack of coating, lack of printing, and so on. 2. Causes and countermeasures of wrinkles
The wrinkles caused by the slitting of the film have various forms such as wrinkles, longitudinal wrinkles, cross wrinkles, and line wrinkles, and the causes are also different, as follows:
(1) Wrinkle: also known as bottom wrinkle, initial wrinkle, etc., is the wrinkle appearing in the section of the original winding film of the paper core. Since the wrinkle is mostly irregular wrinkles, the user generally uses the film to wrinkle. Disposal. The degree of wrinkling is an important indicator reflecting the level of cutting technology of a BOPP film company. The film produced by different companies has a wrinkle length ranging from a few meters, tens of meters to several hundred meters, and the more serious the wrinkles, the more The greater the losses caused by users, therefore, each film company is committed to improving the research of slitting and wrinkle. Through many years, the BOPP industry has carried out a series of intensive and meticulous work on solving the problem of wrinkling. From the two aspects of process parameter screening and equipment adjustment and transformation, we have found a set of effective solutions and received very good results. effect,

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com