Bopp Tape Slitting Machine Price

Bopp Tape Slitting Machine Price

Inspection and preparation before the cutting machine is turned on
4.1.1. Confirm that the main power supply voltage is 380V.
4.1.2. Turn on each power switch and check if the electricity and gas supply are normal.
4.1.3. Before starting the machine, you must confirm that the surface of each guide roller is smooth and free of burr dust, debris, etc. When cleaning the machine, use alcohol or water to soft cloth.
Wipe, can not be wiped with other solvents, remove the impurities around the equipment and production, to ensure normal production;
4.1.4. Obtain all kinds of accessories and tools such as slitting products and tapes in strict accordance with the production instruction sheet and the process card requirements.
4.1.4.1. Receive the composite film specified on the production instruction sheet, check whether the composite film tracking card is complete, and describe the previous quality problem is it clear.
4.1.4.2. Confirm the cut specifications, roll direction, batch number, material structure, winding diameter or meter number according to the production order. 4.1.5. Carefully check the equipment to confirm that each rewinding mechanism, EPC device, and tension control system are normal, and confirm static electricity.
Whether the elimination is normal or not;
4.1.6. The unwinding material is ready, and then the film is routed in the correct way;
4.1.7. Prepare the winding paper core according to the slitting specifications and place it in the corresponding position of the winding reel.

Bopp Tape Slitting Machine Price

Slitting machine operating procedures -

Third, through the film:

9. Press “Device Jog” again, and the film on both sides will be flattened until the slitting film appears on the winding side 2, and the film is cut with a knife.
10. Manually pull the slit film on the winding side 1 and the winding side 2, bond the film to the corresponding paper core, and tighten the film and stick the flat film to the paper core (note the side 1 and side 2 films). Wearing different methods).
11. Manually adjust the leading edge probe into position.
12. Set the winding length and winding diameter on the operation screen (see the preset length and diameter method for details)

Bopp Tape Slitting Machine Price

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

One. Winding too loose / too tight
     Among the many factors affecting the quality of product use, the tightness of the film roll is critical, and the tightness control is moderate, which not only ensures the quality of the slitting, but also compensates for the quality defects caused by the film making process, but the tightness of the winding. Improper control will inevitably directly affect the quality of the product. As a metaphor, if we compare the film formation to the process of producing rice, the cutting is the cook of the rice. The quality of the rice is important, but the cooking time can not be sloppy, in the various control indicators of the cutting. The grasp of the tightness of the winding is like grasping the amount of rice water used in the cooking process. The lack of water and water must have a direct impact on the quality of the rice.

(1) Several methods for judging the tightness of winding
1. Acupressure test method: the examiner presses the surface or end face of the film roll by hand to judge
Whether the volume tightness is suitable. This is a commonly used test method. The advantages are fast, intuitive, and highly reliable, but it requires some experience, lack of data support, and difficulty in recording. 2. Hardness measurement method: The hardness is measured by using a durometer, and the data is spoken.
The advantages are scientific, quantitative, convenient recording, and less disputes on judgment differences. The disadvantage is that only the surface of the film roll can be detected, and the facts inside the film roll cannot be reflected.
3. Visual analysis method: judging the film roll by visually changing the color change of the end face of the film roll or the shape of the end face
For the same product, the darker the end face, the tighter the winding, especially at the near paper tube. The tightness of the winding is often black; for the end shape, the star is the best. According to the judgment, the appearance of a single star may be the phenomenon of tightness of the film, and the occurrence of double stars should be caused by the tightness of the film. The advantages of visual methods are fast and accurate, but they can only analyze some individual winding problems, which is not comprehensive enough.
4. Process tapping method: tapping the membrane surface with a rigid object during the slitting and winding process, through the feel
And the sound to judge the tightness of the film roll, this method can track the film winding tightness from the inside to the outside, the accuracy and credibility are higher, but it will damage the film surface and have certain operation. Dangerousness, we have forbidden to use this method to test the tightness of film roll since 2000. This method is currently only suitable for non-conventional occasions such as product development, slitting control analysis.
Although the current tapping method is not allowed, we use a combination of acupressure test, hardness measurement and visual analysis in the daily slitting process. There is sufficient means to accurately determine the tightness of the winding. Judge. Since the hardness test method is less used in the film industry, the time for using this method is also short. The test method is introduced below.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com