Used Bopp Tape Machine

Used Bopp Tape Machine

Inspection and preparation before the cutting machine is turned on
4.1.1. Confirm that the main power supply voltage is 380V.
4.1.2. Turn on each power switch and check if the electricity and gas supply are normal.
4.1.3. Before starting the machine, you must confirm that the surface of each guide roller is smooth and free of burr dust, debris, etc. When cleaning the machine, use alcohol or water to soft cloth.
Wipe, can not be wiped with other solvents, remove the impurities around the equipment and production, to ensure normal production;
4.1.4. Obtain all kinds of accessories and tools such as slitting products and tapes in strict accordance with the production instruction sheet and the process card requirements.
4.1.4.1. Receive the composite film specified on the production instruction sheet, check whether the composite film tracking card is complete, and describe the previous quality problem is it clear.
4.1.4.2. Confirm the cut specifications, roll direction, batch number, material structure, winding diameter or meter number according to the production order. 4.1.5. Carefully check the equipment to confirm that each rewinding mechanism, EPC device, and tension control system are normal, and confirm static electricity.
Whether the elimination is normal or not;
4.1.6. The unwinding material is ready, and then the film is routed in the correct way;
4.1.7. Prepare the winding paper core according to the slitting specifications and place it in the corresponding position of the winding reel.

Used Bopp Tape Machine

Slitting machine operating procedures -

Third, through the film:

14. Press the “MACHINE” button, the siren will sound and the signal light will flash yellow. Confirm that the personnel are in the safe area, press "machine on" again, the button light is always on, the machine starts and accelerates to the input set speed.
15. If necessary, perform parent roll adjustment, brake tension adjustment, and flattening roller position check at low speed.

Used Bopp Tape Machine

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

(2) The purpose, method and characteristics of hardness testing

 

3. Method for detecting film roll hardness
1 selection of testing equipment
There are various instruments for detecting the hardness of an object, but so far there has not been a hardness tester that professionally detects the hardness of a film roll. Due to the large difference in surface hardness between various objects and the variety of hardness testers, it is important to select a hardness tester that can effectively reflect the tightness of the film roll. After screening and comparison, our company has determined the "A-type rubber hardness tester" for detecting the surface hardness of rubber products as an auxiliary instrument for detecting the tightness of the film roll.
2 detection instrument correction
Since the "A type rubber hardness tester" is not a special test instrument for the film roll, in order to improve the detection accuracy of the instrument, we have modified the structure of the hardness tester according to the characteristics of the film, and increased the presser area by 5 times.
3 detection methods a.
Before the test, the pointer of the hardness tester should be in the free state and point to the zero position. When pressing the hardness tester on the glass plate, the pointer should be 100 degrees (the end face of the press pin and the bottom of the foot are in close contact with the glass). If the zero position and the 100 degree are not indicated, the needle can be pressed slightly several times, if not When referring to zero and 100 degrees, it cannot be used. The hardness tester to be confirmed can be used again if it meets the requirements for use. b.
When testing the hardness, put the hardness tester on the side of the film product, take the left, middle and right positions, at least 40mm from the edge of the film roll, and firmly press the end of the hardness tester with both hands, so that the pressure pin is pressed vertically. The sample is read within 1 s until the pressure is fully contacted with the sample, and the average is taken and recorded.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com