Used Bopp Tape Slitting Machine

Used Bopp Tape Slitting Machine

Inspection and preparation before the cutting machine is turned on
4.1.1. Confirm that the main power supply voltage is 380V.
4.1.2. Turn on each power switch and check if the electricity and gas supply are normal.
4.1.3. Before starting the machine, you must confirm that the surface of each guide roller is smooth and free of burr dust, debris, etc. When cleaning the machine, use alcohol or water to soft cloth.
Wipe, can not be wiped with other solvents, remove the impurities around the equipment and production, to ensure normal production;
4.1.4. Obtain all kinds of accessories and tools such as slitting products and tapes in strict accordance with the production instruction sheet and the process card requirements.
4.1.4.1. Receive the composite film specified on the production instruction sheet, check whether the composite film tracking card is complete, and describe the previous quality problem is it clear.
4.1.4.2. Confirm the cut specifications, roll direction, batch number, material structure, winding diameter or meter number according to the production order. 4.1.5. Carefully check the equipment to confirm that each rewinding mechanism, EPC device, and tension control system are normal, and confirm static electricity.
Whether the elimination is normal or not;
4.1.6. The unwinding material is ready, and then the film is routed in the correct way;
4.1.7. Prepare the winding paper core according to the slitting specifications and place it in the corresponding position of the winding reel.

Used Bopp Tape Slitting Machine

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

(iv) Effect of film roll tightness on product quality
1. The winding is too tight:
1 fluttering/starting bone: As BOPP film, it is normal for the thickness of the product to fluctuate within a reasonable range. If the reeling tightness is appropriate, this thickness fluctuation will not affect the quality of use, but when the slitting is too tight The thicker layers of the film are stacked together to cause edge thickness or bone swelling, which affects the quality of use. The fluttering or bone formation that is formed by over-tightening is often difficult to find during the slitting process, but after the product has been stored for a period of time, the problem will be highlighted. In addition, there are several types of products with uneven thickness defects that can be easily revealed, such as ultra-transparent tape film, crystal film, heat sealing film, etc., while fluttering and bone-starting phenomenon will cause different quality of all film products. The degree of influence, especially for products that require printing and processing, is particularly prominent.
2 Adhesion: over-tightening of double-sided corona products, anti-corona products and products with less anti-adhesive content will cause adhesion quality problems, and the problem can only be found in the customer's use, the impact is great, and appears Products with adhesion problems can only be disposed of as scrapping, causing large losses to the company.
3 Face wrinkles: Due to the tight winding, the film cushioning performance is degraded. The wrinkles formed by the extrusion of the film on the end face of the product during handling and loading and unloading are difficult to eliminate, forming the end wrinkles and affecting the quality of the product.
4 Pitting: Due to the tightness of the winding, the film near the paper tube is affected by the rough surface of the paper tube, which causes pitting, which affects the quality of the product. The use of the polished paper tube will eliminate the surface of the film and improve it. Start wrinkles).

Used Bopp Tape Slitting Machine

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

two. Wrinkle (wrinkle, vertical wrinkle, cross wrinkle, line wrinkle)

Through many years, the BOPP industry has carried out a series of intensive and meticulous work on solving the problem of wrinkling. From the two aspects of process parameter screening and equipment adjustment and transformation, we have found a set of effective solutions and received very good results. effect,
Methods include:

5 Under the same parameters, the long gauge is more likely to wrinkle than the short gauge film roll, which means that the longer the specification, the worse the exhaust effect, and the lower the strength of the long gauge paper tube, the slitting process paper The slight bending of the tube tends to cause the film in the middle of the film roll to wrinkle for a long time, and when the paper core is long, under the high-speed rotation of the slit, as the axis of the film winding, its straightness, concentricity, strength, The indicators such as surface finish are the most important. Generally speaking, the longer the paper core, the more difficult it is to ensure the straightness and concentricity. Therefore, the quality of the paper core is very important. It is necessary to improve the inspection of the paper core. If the paper tube is found during the slitting process, the paper tube is found. The quality is abnormal and needs to be replaced in time. In addition, under the same parameter conditions, the short gauge is more prone to deviation than the long gauge membrane coil, and a large winding pressure is required. Therefore, for the adjustment of the wrinkle, the wrinkle can be reduced by appropriately reducing the pressure setting for the long specification, and the pressure is increased for the short specification to prevent the deviation;
6 Different thickness films have different degrees of wrinkling, thick film stiffness is better, less wrinkles, thin film is more open, so the thin film should be adjusted to increase the strength of the parameters to overcome For the generation of wrinkles, different thickness of the film should have different special data for slitting;
7 The product that is slit inside and outside the slitting machine may have different degrees of wrinkling due to the different angles (wrap angles) entering the winding roller. The difference between the inner and outer wrinkles of each slitting machine should be compared, such as The difference is obvious. During the slitting process, the specification that is prone to wrinkle should be cut on the side that is not prone to wrinkle;
8 The wrinkle reduction can also be achieved by adjusting the venting performance of the pressure roller and improving the stability of the winding arm.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com