Adhesive Tape Slitting Machine Suppliers

Adhesive Tape Slitting Machine Suppliers

Preparation of slitter cutter
1. Razor slitting
1.1. The razor slitting requires the film to travel in the correct direction to the winding section.
1.2. Adjust the photoelectric tracking to bring the film to the proper position.
1.3. Tension the film and attach the blade to the razor holder.
1.4. According to the specifications required by the instruction sheet, the sliding razor holder is cut into the razor groove under the film, and the blade edge and the edge of the sipe are required to be in contact with each other.
1.5 After adjusting the depth of the cutter, lock the razor frame screws.
2. Round knife cutting
2.1. Check whether the upper and lower knives are sharp and have no gaps, and vice versa;
2.2. Determine the number of knives (N+1) according to the number of product series (N);
2.3. Install the lower knife to adjust the width of the lower knife according to the actual width of the product;
2.4 Install the upper knife correctly. The flat side of the upper knife is aligned with the side of the lower cutting edge. The upper knife is aligned with the gap between the lower knife and the septum. Press the screws on both sides to make the upper knife enter the gap depth to about 2mm. The upper knife is attached to the lower knife and fastened. Finally, the screw on the left side of the upper knife holder is adjusted so that the whole knife holder moves 1-2 mm to the right side and is fastened.

Adhesive Tape Slitting Machine Suppliers

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

(iv) Effect of film roll tightness on product quality

(5) Coping methods
1. Reasonable principle: Applicable is reasonable, which means that the cutting operator and the quality inspector are too loose according to the winding/
Too tightly influence the degree of influence on different products, adjust the cutting process reasonably, and reasonably grasp the tightness of the film roll to meet the requirements of the use of film products.
2. Ningsong Motight principle: objective when cutting equipment status, product specifications, film performance characteristics, etc.
When the influence of the condition causes the winding tightness to be in an inappropriate degree, the principle of tightness is generally used, because the problem of over-tightening often makes the film unusable, except for the special requirements.
3. The principle of primary and secondary: it means that in the process of slitting production, small groups should be followed to the interests of large collectives.
The principle of benefiting the interests of the company, avoiding the pursuit of high output and high distribution for the purpose of reducing the quality of cutting, all should be based on product quality, maintaining the German crown film brand as the responsibility, effectively completing various production and quality indicators Effectively serve the enterprise and users, and strive to be the best supplier of film.
4. System Management Principles: Refers to the use of systematic, scientific management methods, practical, theoretical, and empirical
The accumulated cutting control method is compiled, and according to the optimal combination of different types of products, width, winding length, season and other external variables and slitting tension, pressure and other internal variables, the document control management is performed to form an operation guidance document. Minimize the influence of subjective factors, reduce the impact caused by insufficient individual ability or excessive dependence on experience, and continuously supplement, optimize and improve the operation guidance documents to meet the needs of system management.

Adhesive Tape Slitting Machine Suppliers

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

two. Wrinkle (wrinkle, vertical wrinkle, cross wrinkle, line wrinkle)

Through many years, the BOPP industry has carried out a series of intensive and meticulous work on solving the problem of wrinkling. From the two aspects of process parameter screening and equipment adjustment and transformation, we have found a set of effective solutions and received very good results. effect,
Methods include:
1 The wrinkles near the core of the paper can not be stretched, which is largely related to the contact roller pressure of the slitter. It has been proved that when the contact roller pressure is increased, the wrinkles increase, and when the pressure is reduced, the wrinkles are reduced, and the air inside the film roll is reduced. The amount is increased, so that the gap between the membranes is increased to reduce friction, which is beneficial to reduce wrinkles;
2 When the winding pressure is small, the wrinkle is less, but the small pressure will cause the film roll to run off. Therefore, it is very important to set the pressure curve reasonably. When starting, set a small pressure, when it is easy to wrinkle. After a length of time has passed, the pressure should be increased rapidly to avoid the occurrence of deviation;
3 In the improvement of wrinkle, the control of winding tension should be considered. If only the winding pressure is considered, the initial pressure setting value will be very small. In case of special circumstances, the deceleration will cause deviation due to small pressure. Defects, so the tension curve setting is also very important, and the winding pressure and tension must be matched properly.
4 The pressure at the core of the paper cannot be reduced indefinitely. If it is too small, the inside of the film roll will be too loose, and the end face will appear star-shaped, causing the film to wrinkle. Therefore, it should be adjusted to the film roll when setting the pressure curve. The end face has neither a star shape and minimizes wrinkles;

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com