Mini Tape Slitting Machine

Mini Tape Slitting Machine

Slitting adjustment
1. Put the cutter down, open the curling blower switch, set the winding tension, start the machine, run 2-3 meters, stop;
2. Measure the width of each joint to confirm whether the requirements are met. If there is any error, the ratio of the cutter should be re-matched.
3. Check whether each of the paper cores and the corresponding film are aligned, otherwise adjust them;

Mini Tape Slitting Machine

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

two. Wrinkle (wrinkle, vertical wrinkle, cross wrinkle, line wrinkle)
1. The effect of wrinkles on the quality of use
BOPP film is commonly known as "cellophane", which reflects the film's high stiffness, high transparency and good gloss. The film is wrinkled, which means that the flatness of the film is damaged to a certain extent. This is not allowed for any film. Not only will it affect the appearance of deep-processed products, but also cause quality defects in use, such as lack of coating, lack of printing, and so on. 2. Causes and countermeasures of wrinkles
The wrinkles caused by the slitting of the film have various forms such as wrinkles, longitudinal wrinkles, cross wrinkles, and line wrinkles, and the causes are also different, as follows:
(1) Wrinkle: also known as bottom wrinkle, initial wrinkle, etc., is the wrinkle appearing in the section of the original winding film of the paper core. Since the wrinkle is mostly irregular wrinkles, the user generally uses the film to wrinkle. Disposal. The degree of wrinkling is an important indicator reflecting the level of cutting technology of a BOPP film company. The film produced by different companies has a wrinkle length ranging from a few meters, tens of meters to several hundred meters, and the more serious the wrinkles, the more The greater the losses caused by users, therefore, each film company is committed to improving the research of slitting and wrinkle. Through many years, the BOPP industry has carried out a series of intensive and meticulous work on solving the problem of wrinkling. From the two aspects of process parameter screening and equipment adjustment and transformation, we have found a set of effective solutions and received very good results. effect,

Mini Tape Slitting Machine

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

two. Wrinkle (wrinkle, vertical wrinkle, cross wrinkle, line wrinkle)

Through many years, the BOPP industry has carried out a series of intensive and meticulous work on solving the problem of wrinkling. From the two aspects of process parameter screening and equipment adjustment and transformation, we have found a set of effective solutions and received very good results. effect,
Methods include:
1 The wrinkles near the core of the paper can not be stretched, which is largely related to the contact roller pressure of the slitter. It has been proved that when the contact roller pressure is increased, the wrinkles increase, and when the pressure is reduced, the wrinkles are reduced, and the air inside the film roll is reduced. The amount is increased, so that the gap between the membranes is increased to reduce friction, which is beneficial to reduce wrinkles;
2 When the winding pressure is small, the wrinkle is less, but the small pressure will cause the film roll to run off. Therefore, it is very important to set the pressure curve reasonably. When starting, set a small pressure, when it is easy to wrinkle. After a length of time has passed, the pressure should be increased rapidly to avoid the occurrence of deviation;
3 In the improvement of wrinkle, the control of winding tension should be considered. If only the winding pressure is considered, the initial pressure setting value will be very small. In case of special circumstances, the deceleration will cause deviation due to small pressure. Defects, so the tension curve setting is also very important, and the winding pressure and tension must be matched properly.
4 The pressure at the core of the paper cannot be reduced indefinitely. If it is too small, the inside of the film roll will be too loose, and the end face will appear star-shaped, causing the film to wrinkle. Therefore, it should be adjusted to the film roll when setting the pressure curve. The end face has neither a star shape and minimizes wrinkles;

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com