Tape Slitting Machine Malaysia

Tape Slitting Machine Malaysia

Slitting machine shutdown operation
1. After the cutting is completed, the unloading is stopped;
2. Release the switch and lift the cutter unit.
3. Clean the crimping device and turn off the curling blower.
4. Turn off the photoelectric tracking system.
5. Turn off the power and air supply of the whole machine.
6. Clean up the surrounding environment.
7. Carefully fill in the production daily record, product self-checklist and other work records.

Tape Slitting Machine Malaysia

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

One. Winding too loose / too tight
     Among the many factors affecting the quality of product use, the tightness of the film roll is critical, and the tightness control is moderate, which not only ensures the quality of the slitting, but also compensates for the quality defects caused by the film making process, but the tightness of the winding. Improper control will inevitably directly affect the quality of the product. As a metaphor, if we compare the film formation to the process of producing rice, the cutting is the cook of the rice. The quality of the rice is important, but the cooking time can not be sloppy, in the various control indicators of the cutting. The grasp of the tightness of the winding is like grasping the amount of rice water used in the cooking process. The lack of water and water must have a direct impact on the quality of the rice.

(1) Several methods for judging the tightness of winding
1. Acupressure test method: the examiner presses the surface or end face of the film roll by hand to judge
Whether the volume tightness is suitable. This is a commonly used test method. The advantages are fast, intuitive, and highly reliable, but it requires some experience, lack of data support, and difficulty in recording. 2. Hardness measurement method: The hardness is measured by using a durometer, and the data is spoken.
The advantages are scientific, quantitative, convenient recording, and less disputes on judgment differences. The disadvantage is that only the surface of the film roll can be detected, and the facts inside the film roll cannot be reflected.
3. Visual analysis method: judging the film roll by visually changing the color change of the end face of the film roll or the shape of the end face
For the same product, the darker the end face, the tighter the winding, especially at the near paper tube. The tightness of the winding is often black; for the end shape, the star is the best. According to the judgment, the appearance of a single star may be the phenomenon of tightness of the film, and the occurrence of double stars should be caused by the tightness of the film. The advantages of visual methods are fast and accurate, but they can only analyze some individual winding problems, which is not comprehensive enough.
4. Process tapping method: tapping the membrane surface with a rigid object during the slitting and winding process, through the feel
And the sound to judge the tightness of the film roll, this method can track the film winding tightness from the inside to the outside, the accuracy and credibility are higher, but it will damage the film surface and have certain operation. Dangerousness, we have forbidden to use this method to test the tightness of film roll since 2000. This method is currently only suitable for non-conventional occasions such as product development, slitting control analysis.
Although the current tapping method is not allowed, we use a combination of acupressure test, hardness measurement and visual analysis in the daily slitting process. There is sufficient means to accurately determine the tightness of the winding. Judge. Since the hardness test method is less used in the film industry, the time for using this method is also short. The test method is introduced below.

Tape Slitting Machine Malaysia

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

two. Wrinkle (wrinkle, vertical wrinkle, cross wrinkle, line wrinkle)

Through many years, the BOPP industry has carried out a series of intensive and meticulous work on solving the problem of wrinkling. From the two aspects of process parameter screening and equipment adjustment and transformation, we have found a set of effective solutions and received very good results. effect,
Methods include:

5 Under the same parameters, the long gauge is more likely to wrinkle than the short gauge film roll, which means that the longer the specification, the worse the exhaust effect, and the lower the strength of the long gauge paper tube, the slitting process paper The slight bending of the tube tends to cause the film in the middle of the film roll to wrinkle for a long time, and when the paper core is long, under the high-speed rotation of the slit, as the axis of the film winding, its straightness, concentricity, strength, The indicators such as surface finish are the most important. Generally speaking, the longer the paper core, the more difficult it is to ensure the straightness and concentricity. Therefore, the quality of the paper core is very important. It is necessary to improve the inspection of the paper core. If the paper tube is found during the slitting process, the paper tube is found. The quality is abnormal and needs to be replaced in time. In addition, under the same parameter conditions, the short gauge is more prone to deviation than the long gauge membrane coil, and a large winding pressure is required. Therefore, for the adjustment of the wrinkle, the wrinkle can be reduced by appropriately reducing the pressure setting for the long specification, and the pressure is increased for the short specification to prevent the deviation;
6 Different thickness films have different degrees of wrinkling, thick film stiffness is better, less wrinkles, thin film is more open, so the thin film should be adjusted to increase the strength of the parameters to overcome For the generation of wrinkles, different thickness of the film should have different special data for slitting;
7 The product that is slit inside and outside the slitting machine may have different degrees of wrinkling due to the different angles (wrap angles) entering the winding roller. The difference between the inner and outer wrinkles of each slitting machine should be compared, such as The difference is obvious. During the slitting process, the specification that is prone to wrinkle should be cut on the side that is not prone to wrinkle;
8 The wrinkle reduction can also be achieved by adjusting the venting performance of the pressure roller and improving the stability of the winding arm.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com