Automated Tape Slitter

Automated Tape Slitter

Tape slitting machine principle:
1. The paper slitting machine shall carry out the fixed length slitting processing of the whole roll or the whole raw material, such as plastic packaging materials, packaging carton, steel plate, film, leather, wood chip, etc., and the fixed length slitting control shall be used.
2. The slitting length can be set continuously. If there is an error in the actual slitting length, it is easy to calibrate by setting parameters.
3. The slitting control of the paper slitter is divided into static and dynamic slitting: it stops accurately when the set length arrives, then static slitting processing, restarts after slitting; when the set length arrives, it does not stop. The slitting signal is dynamically slitted during the material movement process.

Automated Tape Slitter

Slitting machine operating procedures -

Third, through the film:

5. Press “Release Brake” again until the indicator light flashes and the unwinder brakes.
6. Press and hold the “Pinch with chain” button, the film is pulled through the chain to the sipe roll, and the film is removed from the shackle on the chain.
7. Press “Device Jog”, the film moves along the machine running direction to the winding side 2, both sides are pulled out, release the button, and flatten the film.
8. The “cutting knife switch” is in the open position, and all the cutting cutters that need to be cut are marked.

Automated Tape Slitter

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

two. Wrinkle (wrinkle, vertical wrinkle, cross wrinkle, line wrinkle)

Through many years, the BOPP industry has carried out a series of intensive and meticulous work on solving the problem of wrinkling. From the two aspects of process parameter screening and equipment adjustment and transformation, we have found a set of effective solutions and received very good results. effect,
Methods include:

5 Under the same parameters, the long gauge is more likely to wrinkle than the short gauge film roll, which means that the longer the specification, the worse the exhaust effect, and the lower the strength of the long gauge paper tube, the slitting process paper The slight bending of the tube tends to cause the film in the middle of the film roll to wrinkle for a long time, and when the paper core is long, under the high-speed rotation of the slit, as the axis of the film winding, its straightness, concentricity, strength, The indicators such as surface finish are the most important. Generally speaking, the longer the paper core, the more difficult it is to ensure the straightness and concentricity. Therefore, the quality of the paper core is very important. It is necessary to improve the inspection of the paper core. If the paper tube is found during the slitting process, the paper tube is found. The quality is abnormal and needs to be replaced in time. In addition, under the same parameter conditions, the short gauge is more prone to deviation than the long gauge membrane coil, and a large winding pressure is required. Therefore, for the adjustment of the wrinkle, the wrinkle can be reduced by appropriately reducing the pressure setting for the long specification, and the pressure is increased for the short specification to prevent the deviation;
6 Different thickness films have different degrees of wrinkling, thick film stiffness is better, less wrinkles, thin film is more open, so the thin film should be adjusted to increase the strength of the parameters to overcome For the generation of wrinkles, different thickness of the film should have different special data for slitting;
7 The product that is slit inside and outside the slitting machine may have different degrees of wrinkling due to the different angles (wrap angles) entering the winding roller. The difference between the inner and outer wrinkles of each slitting machine should be compared, such as The difference is obvious. During the slitting process, the specification that is prone to wrinkle should be cut on the side that is not prone to wrinkle;
8 The wrinkle reduction can also be achieved by adjusting the venting performance of the pressure roller and improving the stability of the winding arm.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com