Automated Tape Slitting Rewinding Machine

Automated Tape Slitting Rewinding Machine

Tape slitting machine principle:
1. The paper slitting machine shall carry out the fixed length slitting processing of the whole roll or the whole raw material, such as plastic packaging materials, packaging carton, steel plate, film, leather, wood chip, etc., and the fixed length slitting control shall be used.
2. The slitting length can be set continuously. If there is an error in the actual slitting length, it is easy to calibrate by setting parameters.
3. The slitting control of the paper slitter is divided into static and dynamic slitting: it stops accurately when the set length arrives, then static slitting processing, restarts after slitting; when the set length arrives, it does not stop. The slitting signal is dynamically slitted during the material movement process.

Automated Tape Slitting Rewinding Machine

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

(2) The purpose, method and characteristics of hardness testing
1. OBJECTIVE: The hardness test method provides a quantifiable means for determining the tightness of the film roll and provides a quantifiable basis for the determination.
Some of the product quality characteristics can be quantitative, and some can not be quantified, can only be qualitative. In the past, our judgment on the tightness of the film winding is only based on the hand feeling. The scale of the judgment is difficult to grasp, and the difference between different inspectors Larger. In actual work, when measuring, the non-quantitative characteristics are usually converted into quantifiable substitute quality characteristics, which are used as the basis for evaluation, inspection and assessment. Film roll hardness testing is a means of quantitative control of the main quality characteristics of the slitting under this guiding ideology. However, it is worth emphasizing that not all quality characteristics must be quantified, especially the film as a process material quality characteristic, there are quantitative measurement characteristics, such as thickness, tensile strength, gloss, etc., also have qualitative characteristics, only the process Subjective judgments such as wrinkles, blots, chromatic aberrations, etc.

2. Several characteristics of film roll hardness
1 Different film varieties, the hand tightness is similar but the hardness data is different. This is because the hand roll is used to squeeze the film roll in a certain area of ??the finger, which is a test of one surface, and when the hardness tester is used, it is a The pin point is pressed against the film roll, which is a detection of a point, and there will be differences between the two;
2 different film varieties have different winding hardness requirements, which are based on the characteristics and uses of various films;
3 The tightness and hardness of the film roll are not completely linear. The most sensitive value is between 87 and 95. When the hardness is as low as 85, the rewinding does not affect the hardness. Similarly, when the hardness is high. At 97 o'clock, the effect of rewinding on the film roll hardness is getting smaller and smaller.
4 Winding hardness is a reference index for quantifying the winding tightness. It only reflects a quality characteristic of the film roll surface and does not reflect the fullness of the film roll. Therefore, the key is to effectively control the film roll tightness. The quality of the product used.

Automated Tape Slitting Rewinding Machine

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

(iv) Effect of film roll tightness on product quality
1. The winding is too tight:
1 fluttering/starting bone: As BOPP film, it is normal for the thickness of the product to fluctuate within a reasonable range. If the reeling tightness is appropriate, this thickness fluctuation will not affect the quality of use, but when the slitting is too tight The thicker layers of the film are stacked together to cause edge thickness or bone swelling, which affects the quality of use. The fluttering or bone formation that is formed by over-tightening is often difficult to find during the slitting process, but after the product has been stored for a period of time, the problem will be highlighted. In addition, there are several types of products with uneven thickness defects that can be easily revealed, such as ultra-transparent tape film, crystal film, heat sealing film, etc., while fluttering and bone-starting phenomenon will cause different quality of all film products. The degree of influence, especially for products that require printing and processing, is particularly prominent.
2 Adhesion: over-tightening of double-sided corona products, anti-corona products and products with less anti-adhesive content will cause adhesion quality problems, and the problem can only be found in the customer's use, the impact is great, and appears Products with adhesion problems can only be disposed of as scrapping, causing large losses to the company.
3 Face wrinkles: Due to the tight winding, the film cushioning performance is degraded. The wrinkles formed by the extrusion of the film on the end face of the product during handling and loading and unloading are difficult to eliminate, forming the end wrinkles and affecting the quality of the product.
4 Pitting: Due to the tightness of the winding, the film near the paper tube is affected by the rough surface of the paper tube, which causes pitting, which affects the quality of the product. The use of the polished paper tube will eliminate the surface of the film and improve it. Start wrinkles).

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com