Slitting Machine For Skotch Tape

Slitting Machine For Skotch Tape

Tape slitting machine principle:
1. The paper slitting machine shall carry out the fixed length slitting processing of the whole roll or the whole raw material, such as plastic packaging materials, packaging carton, steel plate, film, leather, wood chip, etc., and the fixed length slitting control shall be used.
2. The slitting length can be set continuously. If there is an error in the actual slitting length, it is easy to calibrate by setting parameters.
3. The slitting control of the paper slitter is divided into static and dynamic slitting: it stops accurately when the set length arrives, then static slitting processing, restarts after slitting; when the set length arrives, it does not stop. The slitting signal is dynamically slitted during the material movement process.

Slitting Machine For Skotch Tape

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

(2) The purpose, method and characteristics of hardness testing

 

3. Method for detecting film roll hardness
1 selection of testing equipment
There are various instruments for detecting the hardness of an object, but so far there has not been a hardness tester that professionally detects the hardness of a film roll. Due to the large difference in surface hardness between various objects and the variety of hardness testers, it is important to select a hardness tester that can effectively reflect the tightness of the film roll. After screening and comparison, our company has determined the "A-type rubber hardness tester" for detecting the surface hardness of rubber products as an auxiliary instrument for detecting the tightness of the film roll.
2 detection instrument correction
Since the "A type rubber hardness tester" is not a special test instrument for the film roll, in order to improve the detection accuracy of the instrument, we have modified the structure of the hardness tester according to the characteristics of the film, and increased the presser area by 5 times.
3 detection methods a.
Before the test, the pointer of the hardness tester should be in the free state and point to the zero position. When pressing the hardness tester on the glass plate, the pointer should be 100 degrees (the end face of the press pin and the bottom of the foot are in close contact with the glass). If the zero position and the 100 degree are not indicated, the needle can be pressed slightly several times, if not When referring to zero and 100 degrees, it cannot be used. The hardness tester to be confirmed can be used again if it meets the requirements for use. b.
When testing the hardness, put the hardness tester on the side of the film product, take the left, middle and right positions, at least 40mm from the edge of the film roll, and firmly press the end of the hardness tester with both hands, so that the pressure pin is pressed vertically. The sample is read within 1 s until the pressure is fully contacted with the sample, and the average is taken and recorded.

Slitting Machine For Skotch Tape

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

two. Wrinkle (wrinkle, vertical wrinkle, cross wrinkle, line wrinkle)
1. The effect of wrinkles on the quality of use
BOPP film is commonly known as "cellophane", which reflects the film's high stiffness, high transparency and good gloss. The film is wrinkled, which means that the flatness of the film is damaged to a certain extent. This is not allowed for any film. Not only will it affect the appearance of deep-processed products, but also cause quality defects in use, such as lack of coating, lack of printing, and so on. 2. Causes and countermeasures of wrinkles
The wrinkles caused by the slitting of the film have various forms such as wrinkles, longitudinal wrinkles, cross wrinkles, and line wrinkles, and the causes are also different, as follows:
(1) Wrinkle: also known as bottom wrinkle, initial wrinkle, etc., is the wrinkle appearing in the section of the original winding film of the paper core. Since the wrinkle is mostly irregular wrinkles, the user generally uses the film to wrinkle. Disposal. The degree of wrinkling is an important indicator reflecting the level of cutting technology of a BOPP film company. The film produced by different companies has a wrinkle length ranging from a few meters, tens of meters to several hundred meters, and the more serious the wrinkles, the more The greater the losses caused by users, therefore, each film company is committed to improving the research of slitting and wrinkle. Through many years, the BOPP industry has carried out a series of intensive and meticulous work on solving the problem of wrinkling. From the two aspects of process parameter screening and equipment adjustment and transformation, we have found a set of effective solutions and received very good results. effect,

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com