Slitting Rewinding Machine For Packing Tape

Slitting Rewinding Machine For Packing Tape

Tape slitter setting control:
1. Set the slitting menu according to the type, thickness, length, width, etc. of the film arranged in the slitting plan.
2. Lift the corresponding BOPP film file from the PDF.
3. Set the winding length and width of the film of the corresponding specification.
4. Select the corresponding winding station, adjust the pressure roller arm and pressure roller, and install the paper core of the corresponding specifications.

Slitting Rewinding Machine For Packing Tape

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

(2) The purpose, method and characteristics of hardness testing

 

3. Method for detecting film roll hardness
1 selection of testing equipment
There are various instruments for detecting the hardness of an object, but so far there has not been a hardness tester that professionally detects the hardness of a film roll. Due to the large difference in surface hardness between various objects and the variety of hardness testers, it is important to select a hardness tester that can effectively reflect the tightness of the film roll. After screening and comparison, our company has determined the "A-type rubber hardness tester" for detecting the surface hardness of rubber products as an auxiliary instrument for detecting the tightness of the film roll.
2 detection instrument correction
Since the "A type rubber hardness tester" is not a special test instrument for the film roll, in order to improve the detection accuracy of the instrument, we have modified the structure of the hardness tester according to the characteristics of the film, and increased the presser area by 5 times.
3 detection methods a.
Before the test, the pointer of the hardness tester should be in the free state and point to the zero position. When pressing the hardness tester on the glass plate, the pointer should be 100 degrees (the end face of the press pin and the bottom of the foot are in close contact with the glass). If the zero position and the 100 degree are not indicated, the needle can be pressed slightly several times, if not When referring to zero and 100 degrees, it cannot be used. The hardness tester to be confirmed can be used again if it meets the requirements for use. b.
When testing the hardness, put the hardness tester on the side of the film product, take the left, middle and right positions, at least 40mm from the edge of the film roll, and firmly press the end of the hardness tester with both hands, so that the pressure pin is pressed vertically. The sample is read within 1 s until the pressure is fully contacted with the sample, and the average is taken and recorded.

Slitting Rewinding Machine For Packing Tape

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

(iv) Effect of film roll tightness on product quality
1. The winding is too tight:
1 fluttering/starting bone: As BOPP film, it is normal for the thickness of the product to fluctuate within a reasonable range. If the reeling tightness is appropriate, this thickness fluctuation will not affect the quality of use, but when the slitting is too tight The thicker layers of the film are stacked together to cause edge thickness or bone swelling, which affects the quality of use. The fluttering or bone formation that is formed by over-tightening is often difficult to find during the slitting process, but after the product has been stored for a period of time, the problem will be highlighted. In addition, there are several types of products with uneven thickness defects that can be easily revealed, such as ultra-transparent tape film, crystal film, heat sealing film, etc., while fluttering and bone-starting phenomenon will cause different quality of all film products. The degree of influence, especially for products that require printing and processing, is particularly prominent.
2 Adhesion: over-tightening of double-sided corona products, anti-corona products and products with less anti-adhesive content will cause adhesion quality problems, and the problem can only be found in the customer's use, the impact is great, and appears Products with adhesion problems can only be disposed of as scrapping, causing large losses to the company.
3 Face wrinkles: Due to the tight winding, the film cushioning performance is degraded. The wrinkles formed by the extrusion of the film on the end face of the product during handling and loading and unloading are difficult to eliminate, forming the end wrinkles and affecting the quality of the product.
4 Pitting: Due to the tightness of the winding, the film near the paper tube is affected by the rough surface of the paper tube, which causes pitting, which affects the quality of the product. The use of the polished paper tube will eliminate the surface of the film and improve it. Start wrinkles).

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com