Bopp Jumbo Roll Tape Slitter

Bopp Jumbo Roll Tape Slitter

Inspection and preparation before the cutting machine is turned on
4.1.1. Confirm that the main power supply voltage is 380V.
4.1.2. Turn on each power switch and check if the electricity and gas supply are normal.
4.1.3. Before starting the machine, you must confirm that the surface of each guide roller is smooth and free of burr dust, debris, etc. When cleaning the machine, use alcohol or water to soft cloth.
Wipe, can not be wiped with other solvents, remove the impurities around the equipment and production, to ensure normal production;
4.1.4. Obtain all kinds of accessories and tools such as slitting products and tapes in strict accordance with the production instruction sheet and the process card requirements.
4.1.4.1. Receive the composite film specified on the production instruction sheet, check whether the composite film tracking card is complete, and describe the previous quality problem is it clear.
4.1.4.2. Confirm the cut specifications, roll direction, batch number, material structure, winding diameter or meter number according to the production order. 4.1.5. Carefully check the equipment to confirm that each rewinding mechanism, EPC device, and tension control system are normal, and confirm static electricity.
Whether the elimination is normal or not;
4.1.6. The unwinding material is ready, and then the film is routed in the correct way;
4.1.7. Prepare the winding paper core according to the slitting specifications and place it in the corresponding position of the winding reel.

Bopp Jumbo Roll Tape Slitter

Reasons, countermeasures and effects of BOPP film slitting quality ---

four. Deviation
Deviation refers to the phenomenon that part of the film on the end face of the film roll is misaligned, which is caused by the sliding of the film during the winding process.

2. Causes and countermeasures of deviation:
(1) The problem of the quality of the slitting in the same category as the deviation of the end face is, in terms of degree, the degree of misalignment is more serious than the misalignment of the end face; in terms of nature, the general end face is not a continuous problem. However, the deviation is mostly an accidental problem; from the analysis of the reasons, the cause of the unevenness of the end face may cause the occurrence of the deviation problem.
(2) Since the deviation of the deviation from the end face is more prominent, the eye point should be placed in the fine point when the end face is not aligned. When analyzing the deviation problem, the eye point should be widened, especially the factor of the cutting speed. The effect is that the acceleration and deceleration are too rapid. For a film with good smoothness, it is easy to cause slippage and cause a split layer, and the slitting speed should be slowed down.
(3) For products with narrow slitting, too tight winding of the film roll will cause the film to slip laterally. If the film roll is too loose, air will be trapped, which will cause the film roll end to be staggered. Roll tension.

Bopp Jumbo Roll Tape Slitter

Reasons, countermeasures and effects of BOPP film slitting quality ---

 

six. Burr
Most of the reason for the burrs is that the cutting knife is too blunt, and replacing the cutter can solve the problem. Different types of films have different degrees of wear and tear on the cutters. The thicker the thickness, the greater the wear on the cutters, and the wear of the cutters due to the titanium dioxide and other materials. It is fast, so it is necessary to adjust the blade cutting position or replace the blade according to different cutting objects in time to avoid the appearance of raw products. Due to the high cost of cutting the raw edge product (retrocuting processing cost and edge material loss), it is much higher than the value of the scrapping blade. Therefore, preventive measures should be taken, and the replacement cycle of the blade should be budgeted. Adjust or replace the blade before the problem occurs. Blades reduce losses.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com