Slitter Rewinder Machine Jumbo Roll

Slitter Rewinder Machine Jumbo Roll

Preparation of slitter cutter
1. Razor slitting
1.1. The razor slitting requires the film to travel in the correct direction to the winding section.
1.2. Adjust the photoelectric tracking to bring the film to the proper position.
1.3. Tension the film and attach the blade to the razor holder.
1.4. According to the specifications required by the instruction sheet, the sliding razor holder is cut into the razor groove under the film, and the blade edge and the edge of the sipe are required to be in contact with each other.
1.5 After adjusting the depth of the cutter, lock the razor frame screws.
2. Round knife cutting
2.1. Check whether the upper and lower knives are sharp and have no gaps, and vice versa;
2.2. Determine the number of knives (N+1) according to the number of product series (N);
2.3. Install the lower knife to adjust the width of the lower knife according to the actual width of the product;
2.4 Install the upper knife correctly. The flat side of the upper knife is aligned with the side of the lower cutting edge. The upper knife is aligned with the gap between the lower knife and the septum. Press the screws on both sides to make the upper knife enter the gap depth to about 2mm. The upper knife is attached to the lower knife and fastened. Finally, the screw on the left side of the upper knife holder is adjusted so that the whole knife holder moves 1-2 mm to the right side and is fastened.

Slitter Rewinder Machine Jumbo Roll

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

(iv) Effect of film roll tightness on product quality

2. The volume is too loose:
1 Shift: Due to the looseness of the winding, the film roll is easy to move in series and shifts. If the degree is serious, it cannot be used.
2 Core-pulling: Due to the looseness of the winding, the film roll has serious end face misalignment near the paper tube during the loading or unloading or use process, commonly known as “core pulling”, which affects the appearance and use effect of the product.
3 The film wrinkles produced by the loosening of the rolls and the pit lines (stars) formed by the tightness of the inner pines affect the appearance quality and the use effect of the products to some extent.
4 Face wrinkles: Due to the looseness of the winding, the point support force of the end face of the film roll during the movement is reduced, and the fish scale-like end face wrinkles are easily generated.
5 Eccentricity: If the winding is too loose, the film roll will be eccentric (elliptical), and the unwinding tension will be uneven during the unwinding process, which will affect the use effect, especially the printing overprinting effect.

Slitter Rewinder Machine Jumbo Roll

Reasons, countermeasures and effects of BOPP film slitting quality ---
two. Wrinkles (wrinkles, vertical wrinkles, cross wrinkles, wrinkles)

 

(2) Causes and countermeasures of longitudinal wrinkles
Longitudinal wrinkles mean that the surface of the film roll forms a circumferential rib line. In the process of slitting, a large amount of air entrapment or cumulative thickness unevenness is the main cause of longitudinal streaks, and it is difficult to eliminate the occurrence of a relatively serious stripe. When the longitudinal wrinkles appear in the slitting process, the tension is reduced and the pressure is applied to discharge the air in the film roll to improve the longitudinal wrinkle problem. However, the adjustment range should consider the impact on wrinkles and other aspects (according to relevant professional information, longitudinal wrinkles One of the reasons is that the slitting speed is too fast, and the film roll is most prone to the quality problem of the longitudinal stripe at high speed, but there is no obvious influence in actual production, which remains to be studied). Another reason for the vertical wrinkles is the influence of the running accuracy of the equipment. For equipment with high requirements for running accuracy, after a long period of continuous use, the running accuracy of some components has decreased. For large slitting machines, it is more difficult to ensure the running accuracy due to the large number of running parts. Moreover, since the plastic film is a polymer product, its thickness is very thin, and it is more susceptible to damage during processing. Therefore, once the running accuracy is insufficient, quality problems such as vertical streaks are likely to occur. For this reason, it should be cautious when replacing equipment parts and accessories. It is advisable to use durable and high-precision parts, and it must also ensure a certain precision during installation. Otherwise, it is difficult to meet the operation requirements of the slitting machine.
The flattening roller flattens the film and eliminates some of the longitudinal wrinkles produced by the film under tensile stress.
(3) Causes and countermeasures of cross wrinkles
In addition to the influence of the parent-rolling factor, the transverse wrinkles of the film are mainly caused by the sag-like transverse wrinkles produced by the loosening of the slit film roll. Generally, the slitting process is effective in reducing the wrinkles and reducing the pressure, and should be effective for different types of products. Adjusting the slitting and pressure can effectively eliminate the occurrence of cross wrinkles.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com