Mini Adhesive Tape Slitter Rewinder Machine

Mini Adhesive Tape Slitter Rewinder Machine

Preparation of slitter cutter
1. Razor slitting
1.1. The razor slitting requires the film to travel in the correct direction to the winding section.
1.2. Adjust the photoelectric tracking to bring the film to the proper position.
1.3. Tension the film and attach the blade to the razor holder.
1.4. According to the specifications required by the instruction sheet, the sliding razor holder is cut into the razor groove under the film, and the blade edge and the edge of the sipe are required to be in contact with each other.
1.5 After adjusting the depth of the cutter, lock the razor frame screws.
2. Round knife cutting
2.1. Check whether the upper and lower knives are sharp and have no gaps, and vice versa;
2.2. Determine the number of knives (N+1) according to the number of product series (N);
2.3. Install the lower knife to adjust the width of the lower knife according to the actual width of the product;
2.4 Install the upper knife correctly. The flat side of the upper knife is aligned with the side of the lower cutting edge. The upper knife is aligned with the gap between the lower knife and the septum. Press the screws on both sides to make the upper knife enter the gap depth to about 2mm. The upper knife is attached to the lower knife and fastened. Finally, the screw on the left side of the upper knife holder is adjusted so that the whole knife holder moves 1-2 mm to the right side and is fastened.

Mini Adhesive Tape Slitter Rewinder Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

Eight. Indentation
There are two reasons for the cause of film roll indentation. One is caused by the winding wheel of the film forming process, and the other is caused by the cutting factor. The reasons for the cutting are:
1 Due to the poor adjustment of the angle of the puller wheel, the pressure and tension of the puller wheel are concentrated on one point of the film, and the friction of the contact point causes damage to the film surface to form an indentation.
2 The winding roller is damaged, such as scratches, etc., the degree of film roll indentation is large when the scratch is longitudinal; 3 The winding roller is contaminated, causing the surface of the pressure roller to be uneven, such as adhesive tape, impurities, etc. It will also cause the film roll to be indented and the press roll must be cleaned.
Slight indentation does not affect the use of the product, but it affects the appearance of the product, causing the customer to doubt the quality of the product; the obvious indentation not only affects the appearance of the product, but also attenuates the corona value of the film, affecting the film. Processing performance.

Mini Adhesive Tape Slitter Rewinder Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

nine. Scratch

     In addition, sometimes scratches due to slitting are difficult to detect by the naked eye, but scratches (scratches) will attenuate the corona value of the product. According to experience, the corona value is reduced by about half in the normal cutting process. Dyne, when the corona values ??differ by more than one dyne before and after cutting, the reasons for the cutting process, such as the speed ratio of the driving roller, the quality of the sand skin, the condition of the sipe roll, etc., should be checked to eliminate the influence. .
     It is worth mentioning that there is a kind of abrasion that is caused by the slitting process, but it is mainly caused by the cutting factor. It is mainly that the mother roll is too loose, and the product of the loose part is horizontally or vertically tilted during the slitting process. While scratching the film surface, it is found that the phenomenon is to install the upper splint on the mother roll for positioning, and secondly, the cutting speed should be properly controlled, and the influence of the quality of the mother roll on the cutting quality can be improved as much as possible.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com