Slitting Machine For Bopp Adhesive Tapes

Slitting Machine For Bopp Adhesive Tapes

Preparation of slitter cutter
1. Razor slitting
1.1. The razor slitting requires the film to travel in the correct direction to the winding section.
1.2. Adjust the photoelectric tracking to bring the film to the proper position.
1.3. Tension the film and attach the blade to the razor holder.
1.4. According to the specifications required by the instruction sheet, the sliding razor holder is cut into the razor groove under the film, and the blade edge and the edge of the sipe are required to be in contact with each other.
1.5 After adjusting the depth of the cutter, lock the razor frame screws.
2. Round knife cutting
2.1. Check whether the upper and lower knives are sharp and have no gaps, and vice versa;
2.2. Determine the number of knives (N+1) according to the number of product series (N);
2.3. Install the lower knife to adjust the width of the lower knife according to the actual width of the product;
2.4 Install the upper knife correctly. The flat side of the upper knife is aligned with the side of the lower cutting edge. The upper knife is aligned with the gap between the lower knife and the septum. Press the screws on both sides to make the upper knife enter the gap depth to about 2mm. The upper knife is attached to the lower knife and fastened. Finally, the screw on the left side of the upper knife holder is adjusted so that the whole knife holder moves 1-2 mm to the right side and is fastened.

Slitting Machine For Bopp Adhesive Tapes

Reasons, countermeasures and effects of BOPP film slitting quality ---

nine. Scratch
      Whether the slitting and scratching can be compared and determined by the film surface before and after the slitting, there are various reasons for the scratching of the membrane surface, and the analysis should be based on the appearance of the scratch, such as short-line scratching. The difference of the speed ratio of each drive roller exceeds the process setting requirement, and it needs to be carefully tested and adjusted. If the film surface scratch occurs continuously, the film on the slitter should be inspected for whether it touches the fixed object or cuts each. Whether the roller adheres to dirt such as fine sand grains scratches the film surface.
Scratch is the appearance quality problem of the film, which directly affects the quality appearance of the deep-processed product. Therefore, it is not allowed to exist in the film quality control standard. The slitting process finds that the scratching problem must be carefully checked and quickly eliminated. Since the scratch on the film surface is an irreversible appearance quality problem, it is not allowed to operate the disease when the film surface is scratched, so as to avoid the continuous occurrence of the problem.
      

Slitting Machine For Bopp Adhesive Tapes

Reasons, countermeasures and effects of BOPP film slitting quality ---

ten. Color circle
The color circle is caused by a certain degree of contamination inside or outside the film, which causes the quality of the color circle on the end face of the film roll after slitting and winding. Membrane surface pollution sources come from two aspects. One is the film-forming process. The color circles generated in the front part of the film, such as raw materials, feeding systems, extrusion systems, and die flow channels, generally cause pollution to the inside of the film (core layer). Some color-circle products can clearly observe a large amount of fish-eye impurities in the film. The color circles generated in the film-forming stage and the slitting process mainly cause pollution to the outside (surface) of the film, but whether it is internal or external pollution, It is impossible to remove the impurities from the contaminated film and restore the original appearance. The product with serious color circle has low transparency, the film color is different from the normal product, and it can not be used at all. It can only be reduced to other external treatments, while the products with slight color circles are It has little effect on the transparency of the product and does not affect the use effect of the single film. However, due to the inconspicuous appearance of the color circle product, the “selling phase” is poor, which has a great influence on the image of the German brand. It is not suitable for direct delivery. Secondary processing. If the color circle is caused by external dust pollution factors, the dust will be adsorbed on the surface of the film, resulting in poor quality of heat sealing and poor laser compression.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com