Tape Slitter Rewinder Machine

Tape Slitter Rewinder Machine

Preparation of slitter cutter
1. Razor slitting
1.1. The razor slitting requires the film to travel in the correct direction to the winding section.
1.2. Adjust the photoelectric tracking to bring the film to the proper position.
1.3. Tension the film and attach the blade to the razor holder.
1.4. According to the specifications required by the instruction sheet, the sliding razor holder is cut into the razor groove under the film, and the blade edge and the edge of the sipe are required to be in contact with each other.
1.5 After adjusting the depth of the cutter, lock the razor frame screws.
2. Round knife cutting
2.1. Check whether the upper and lower knives are sharp and have no gaps, and vice versa;
2.2. Determine the number of knives (N+1) according to the number of product series (N);
2.3. Install the lower knife to adjust the width of the lower knife according to the actual width of the product;
2.4 Install the upper knife correctly. The flat side of the upper knife is aligned with the side of the lower cutting edge. The upper knife is aligned with the gap between the lower knife and the septum. Press the screws on both sides to make the upper knife enter the gap depth to about 2mm. The upper knife is attached to the lower knife and fastened. Finally, the screw on the left side of the upper knife holder is adjusted so that the whole knife holder moves 1-2 mm to the right side and is fastened.

Tape Slitter Rewinder Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

twelve. Interface quality problem (poor interface quality, interface identifier does not match)

2. Interface identifier
Due to the large thickness of the film interface, the film roll for some applications must be properly handled at the interface to avoid unnecessary problems, such as slowing down, increasing the gap between the coating blade, and printing the offset plate. The interface products must be identified as necessary to facilitate customer identification and internal management.
1 The color of the adhesive interface is generally beige, special requirements are used according to the regulations. For example, Shanghai Ziquan requires the use of black adhesive tape; the marking method of the joint position is operated according to the regulations, such as Zhuhai Zhongfu Pearl Film, Shenzhen Ruimei The hot film is required to be marked at the ends of the interface with yellow paper dust protruding from the end of the film roll by about 1 cm; other special marks are operated according to the requirements of the production tribe.
2 Require the slitting workshop to mark the length number of the joint product without special requirements after the length of the label in the length column of the package label, and mark the “buter” mark on the note bar of the computer, and mark “+” on the remark column. Marking, pearl film and imitation paper film and exporting pearl film should indicate the length of each product before and after the joint on the length column of the product specification. For special requirements, the relevant marking work should be done according to the regulations (such as Shanghai Ziquan product port). The rate of less than or greater than 25% requires the number of interface products on each board product).

Tape Slitter Rewinder Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

 

thirteen. Foreign matter such as dust and small flying insects in the film roll
In the slitting process of the film, the mother roll film needs to be unwrapped and then slit and wound, which creates conditions for the entry of foreign matter. Since many film products themselves need to be in direct contact with foods, medicines, etc., the hygiene requirements are very strict, and the film is not allowed to be attached with foreign objects such as mosquitoes. Once found, it causes major quality complaints and claims, directly causing the company's economic loss and product brand. Damaged and negatively affected, therefore, the environmental cleaning and purification work in the production workshop plays a very important role in ensuring the quality of the film.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com