Masking Tape Slicer

Masking Tape Slicer

Tape Cutting Machine-
First, the precautions before installation and installation:
1. Install the equipment in a dry, clean and well ventilated place.
2. The equipment should be protected and connected to zero, that is, the casing part is connected with the neutral line in the three-phase four-wire (the product with the power plug is connected to the factory).
3. The power supply in the workplace should be normal, without excessive fluctuations, otherwise the equipment cannot guarantee normal operation.
4. Steps for equipment installation:
a. The power incoming line is connected to the user-supplied three-phase switch of suitable capacity. The three-phase switch shall be fitted with a fuse that meets the requirements and shall not be arbitrarily amplified. The three-phase switch should be dedicated to the cutting machine.
b. The gas source is connected to the inlet end of the filter pressure reducing valve on the rear plate of the cutting chassis through the gas supply pipe, that is, facing the left side joint of the pressure gauge.
c. Clamp the working ground clamp of the cutting machine (the positive output end of the cutting power supply) on the workpiece.

Masking Tape Slicer

GL-704B Four-shaft Auto Roll Cutting Machine

GL-704B Four-shaft Auto Roll Cutting Machine, Suitable for cutting BOPP tape, PVC insulation tape, masking tape, double sided tape, duct tape, medical tape, etc.

 

Product Description

1. Main driving part: Siemens AC motor with inverter is employed.

2.Operating panel part: All functions are operated on the 10" LCD touch panel.

3. Motor control system: The central control system is PLC programmable controller. 

4. Quick shaft change system: Three kinds of shafts are available and quick change of shafts is applied for different materials. 

5. Central control unit: Programmable central control is used and 20 sizes can be set on the same shaft for auto transfer and cutting.

6. Blade feeding positioning system: Blade feeding is controlled by Mitsubishi servo motor, and the cutting speed is adjustable in three stages.

7. Auto exchange device: Cylinder-driven position spline gear is used to ensure fast & precise exchange; non-stop machine to save material loading & unloading time and improve efficiency.

8. Cutting positioning system: Cutting positioning is controlled by Mitsubishi servo motor. The imported high precision ball screw is applied to set the size and the linear slide rail is to bear the load of the cutter seat.

9. Auto angle adjustment of circular blade: Mitsubishi servo motor is used to calculate the circular blade angle and the angle change is subject to different materials (the angle change range is ±8°). 

Masking Tape Slicer

GL-702 Double-shaft Auto Roll Cutting Machine

-------Suitable for cutting BOPP tape, PVC insulation tape, masking tape, double sided tape, duct tape, medical tape, etc.

 

Product Description

1.  Main driving part: Siemens AC motor with inverter is employed.

2. Operating panel: All functions are operated on the 10" LCD touch panel.

3: Motor control system: The central control system is PLC programmable controller. 

4. Central control unit:  Programmable central control is used and 20 sizes can be set on the same shaft for auto transfer and cutting.

5. Blade feeding positioning system:  Blade feeding is controlled by Mitsubishi servo motor,and the cutting speed is adjustable in three stages.

6. Auto angle adjustment of circular blade: Mitsubishi servo motor is used to calculate the circular blade angle and the angle change is subject to different materials (the angle change range is ±8°).

7. Quick shaft change system: Three kinds of shafts are available and quick change of shafts is applied for different materials.

8. Cutting positioning system: Cutting positioning is controlled by Mitsubishi servo motor. The imported high precision ball screw is applied to set the size and the linear slide rail is to bear the load of the cutter seat.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com