Paper Slitter Machine

Paper Slitter Machine

Tape Cutting Machine-

Second, preparation before use:
1. Check the external power supply is correct.
2. Check that the workpiece ground wire is clamped on the workpiece.
3. Turn on the air source and drain the water.
4. Check that the power switch is in the off position.
5. Close the main switch of the power supply of the power grid. At this time, the fan starts to work. Pay attention to check the wind direction. The wind should blow inward. Otherwise, the main transformer will not be ventilated and cooled, which will shorten the working time.
6. Turn the power switch on the panel to the “on” position and the power indicator light. Compressed air should flow out of the torch at this point. Pay attention to whether the pressure gauge pressure gauge pointer is 0.2-0.4 megabytes
Pa position, if the pressure does not match, in the case of gas flow, adjust the upper knob of the filter pressure reducing valve pressure gauge, clockwise to increase pressure, and vice versa.
7. Let the gas flow for a few minutes to remove the condensed water vapor from the torch.

Paper Slitter Machine

Semi-automatic cutting machine technical operation rules

7. Regular inspection of accuracy and variability
7.1 Detect the positive and negative turbulence of the main motion clutch after it is closed. The value is less than 2.0mm.
7.2 Detecting the running speed adjustment range of the host: the minimum speed is not more than 50mm/min, and the maximum speed is not less than 120mm/min.
7.3 Detecting the gas path part includes the connection of the connecting hose: air tightness: oxygen closed circuit 1.2Mpa, mixed gas path: 0.6 Mpa voltage regulation for 20 seconds shall not leak.
7.4 Detecting the thickness range of the cut steel plate: 10-100mm is acceptable.
7.5 Flame burning test of the torch (visible cutting oxygen flow length): 1#≥70mm; 2#≥90mm;3#≥100mm.
8. Daily maintenance regulations
8.1 After cutting the mouth, pay attention to the protective cover of the fashion, and do not bump.
8.2 Pay special attention to moisture when using and storing.
8.3 The lubricant in the gearbox should be replaced in time.

Paper Slitter Machine

Semi-automatic cutting machine technical operation rules

4. Mechanical operation
4.1 All parts must be carefully inspected before use and then tested. At the same time, check the gas distribution valves and torches and the connection path. If there is no problem, ignite and observe whether the flame is normal. If there is no problem, it can be cut.
4.2 When cutting straight lines, it is necessary to put a special track on the steel plate to be cut, select the cutting nozzle according to the cutting thickness, and adjust the speed before cutting.
4.3 Pressure automatic switch and pneumatic valve are normally open. When using automatic pressure switch, the knife switch at the label pressure switch should be pointed in the direction of closing. At this time, the pressure automatic switch is turned on during cutting. When walking, if the automatic switch is not used, the knife switch is pointed to the open position, so that the operation and stop of the cutting machine can be controlled only by controlling the on/off of the power label.
4.5 When cutting the circle, the radius rod should be installed in the screw hole of the body shell and locked, then the tip of the fixed needle should be placed in the hole of the pre-cut center, and the fixed needle can be adjusted to lift the cutting wheel of the cutting machine. To cut, if you need to cut the groove, you can reach the torch by turning it through a certain angle.
4.6 The forward and backward movement of the cutting machine (ie, forward and reverse operation) can be controlled by controlling the middle and reverse signs.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com