Machines For Cutting Aluminum

Machines For Cutting Aluminum

Tape Cutting Machine-

Third, pay attention to the operation process:
1. The torch is in contact with the workpiece and can be cut by pressing the button. Cutting can be started from the edge of the workpiece. When the thickness of the sheet is not large, it can be cut at any point of the workpiece. The torch can be perpendicular to the workpiece
Or slightly inclined to one side, but when opening in the middle of the workpiece, the torch should be tilted slightly to one side in order to blow off the molten metal and cut through the metal.
2. Press the handle button and keep the main circuit on, while the high frequency oscillator works until the cutting arc is formed, and the high frequency oscillator stops working. Thereafter, the cutting can be performed by the movement of the torch. At the same time, the cutting indicator lights.
3. The cutting must be cut through the metal to move evenly, otherwise the nozzle will be damaged. Moving too fast or too slow will affect the quality of the cut.
4, cutting air pressure adjustment: cutting air pressure is too high, the flow is too large, will affect the cutting thickness. If the cutting air pressure is too small, it will affect the service life of the nozzle.
5. Before lifting the torch away from the workpiece, the handle button must be turned on. At this time, the plasma arc is extinguished and the cutting process is stopped.
6. During the cutting process, the arc is re-arced because the torch leaves the workpiece more than 2 mm and the arc is extinguished.
7. When the main transformer temperature exceeds 110 °C due to the connection working time is too long, the thermal protection switch will operate and the device will automatically shut down and cannot be started. It should be restarted after the transformer has cooled down.
8. Always remove the accumulated water in the filter pressure reducing valve, that is, rotate the lowermost screw counterclockwise to remove the water and then tighten. If there is too much water in the compressed air, consider adding a filter valve between the filter pressure reducing valve and the gas source, otherwise the cutting quality will be affected.
9. When the workpiece is not cut, press the torch button as little as possible to avoid damage to the machine.
10. After the cutting workpiece is finished, cut off the power switch and the air supply valve.

Machines For Cutting Aluminum

Semi-automatic cutting machine technical operation rules

7. Regular inspection of accuracy and variability
7.1 Detect the positive and negative turbulence of the main motion clutch after it is closed. The value is less than 2.0mm.
7.2 Detecting the running speed adjustment range of the host: the minimum speed is not more than 50mm/min, and the maximum speed is not less than 120mm/min.
7.3 Detecting the gas path part includes the connection of the connecting hose: air tightness: oxygen closed circuit 1.2Mpa, mixed gas path: 0.6 Mpa voltage regulation for 20 seconds shall not leak.
7.4 Detecting the thickness range of the cut steel plate: 10-100mm is acceptable.
7.5 Flame burning test of the torch (visible cutting oxygen flow length): 1#≥70mm; 2#≥90mm;3#≥100mm.
8. Daily maintenance regulations
8.1 After cutting the mouth, pay attention to the protective cover of the fashion, and do not bump.
8.2 Pay special attention to moisture when using and storing.
8.3 The lubricant in the gearbox should be replaced in time.

Machines For Cutting Aluminum

Semi-automatic cutting machine technical operation rules

5. Control and monitoring methods for mechanical process parameters and characteristics
5.1 When installing the cross rail and main rail, pay attention to the adjustment screw should not be too tight or too loose. 5.2 The cutting tip should be installed so that it should not be tightened too tightly, no air leakage.
5.3 Before using the suction-type torch, the gas injection must be checked and pressed with the finger on the acetylene inlet valve head. Then open the oxygen valve and the acetylene valve. If there is suction on the finger, it means the torch is normal and can be used. If there is no suction, or oxygen flows back from the B-connector, the torch performance is abnormal and must be repaired.
6. Provisions for mechanical supervision and inspection
6.1 The cutting machine should pay attention to the good condition of each part in normal use, and solve the problem if it is found in time.
6.2 Strengthen maintenance and repairs should be carried out every year.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com