Insulation Paper Cutter Machine

Insulation Paper Cutter Machine

Tape Cutting Machine-

Third, pay attention to the operation process:
1. The torch is in contact with the workpiece and can be cut by pressing the button. Cutting can be started from the edge of the workpiece. When the thickness of the sheet is not large, it can be cut at any point of the workpiece. The torch can be perpendicular to the workpiece
Or slightly inclined to one side, but when opening in the middle of the workpiece, the torch should be tilted slightly to one side in order to blow off the molten metal and cut through the metal.
2. Press the handle button and keep the main circuit on, while the high frequency oscillator works until the cutting arc is formed, and the high frequency oscillator stops working. Thereafter, the cutting can be performed by the movement of the torch. At the same time, the cutting indicator lights.
3. The cutting must be cut through the metal to move evenly, otherwise the nozzle will be damaged. Moving too fast or too slow will affect the quality of the cut.
4, cutting air pressure adjustment: cutting air pressure is too high, the flow is too large, will affect the cutting thickness. If the cutting air pressure is too small, it will affect the service life of the nozzle.
5. Before lifting the torch away from the workpiece, the handle button must be turned on. At this time, the plasma arc is extinguished and the cutting process is stopped.
6. During the cutting process, the arc is re-arced because the torch leaves the workpiece more than 2 mm and the arc is extinguished.
7. When the main transformer temperature exceeds 110 °C due to the connection working time is too long, the thermal protection switch will operate and the device will automatically shut down and cannot be started. It should be restarted after the transformer has cooled down.
8. Always remove the accumulated water in the filter pressure reducing valve, that is, rotate the lowermost screw counterclockwise to remove the water and then tighten. If there is too much water in the compressed air, consider adding a filter valve between the filter pressure reducing valve and the gas source, otherwise the cutting quality will be affected.
9. When the workpiece is not cut, press the torch button as little as possible to avoid damage to the machine.
10. After the cutting workpiece is finished, cut off the power switch and the air supply valve.

Insulation Paper Cutter Machine

Guolian Machinery -- GL-5000 Tape Cutting Machine

The tape cutting machine has a counting and cutting length setting function. When using it, the tape should be placed in the tape cutting machine. The tape head should be pulled, then the power is turned on, the switch is turned on, and the setting is set according to the requirements. After that, press the yellow button on the right (start button), and the tape cutter starts to run and cut.

The tape cutter cuts only a piece of tape at a time, and the cut tape is spit out at the gate. The sensor is installed at the gate. If the tape is not removed, the tape cutter will always be in a stagnant state. When we remove the tape, the tape The cutter will start automatically and cut the next tape. Cycle back and forth.

Product parameters:

Cutting length: 5 ~ 999 mm

Tape width: 6 ~ 50 mm

Maximum outer diameter: 300 mm

Speed: 200 mm/min

Weight: 2.8 kg

Size: 115mm X 140mm X 215mm

Insulation Paper Cutter Machine

Automatic tape cutting machine --- Working principle
The working principle of the tape cutting machine is actually the working principle of the laser tape cutting machine, and the technology applied by the laser tape cutting machine is a new cutting technology. Now this technology has been applied to various industries, including tape and metal cutting. A wide range of fields such as glass cutting and engraving.
The laser we usually know is actually a kind of light. It has the same emission principle as other light in nature, but the structure is very different. Although the laser is also light, the laser is dependent on spontaneous emission in the initial very short time. The subsequent process is completely determined by the excitation radiation. Therefore, the laser has a very pure color, almost no divergent directivity, and has a very high luminous intensity. . Through its high coherence, high strength, and high directivity, when the light is irradiated on the tape, the surface of the tape is subjected to strong thermal energy, causing the temperature to rise sharply, forming a rapid melting or vaporization, and completing the cutting.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com