Pvc Cutting Machine Picture

Pvc Cutting Machine Picture

Tape Cutting Machine-

Third, pay attention to the operation process:
1. The torch is in contact with the workpiece and can be cut by pressing the button. Cutting can be started from the edge of the workpiece. When the thickness of the sheet is not large, it can be cut at any point of the workpiece. The torch can be perpendicular to the workpiece
Or slightly inclined to one side, but when opening in the middle of the workpiece, the torch should be tilted slightly to one side in order to blow off the molten metal and cut through the metal.
2. Press the handle button and keep the main circuit on, while the high frequency oscillator works until the cutting arc is formed, and the high frequency oscillator stops working. Thereafter, the cutting can be performed by the movement of the torch. At the same time, the cutting indicator lights.
3. The cutting must be cut through the metal to move evenly, otherwise the nozzle will be damaged. Moving too fast or too slow will affect the quality of the cut.
4, cutting air pressure adjustment: cutting air pressure is too high, the flow is too large, will affect the cutting thickness. If the cutting air pressure is too small, it will affect the service life of the nozzle.
5. Before lifting the torch away from the workpiece, the handle button must be turned on. At this time, the plasma arc is extinguished and the cutting process is stopped.
6. During the cutting process, the arc is re-arced because the torch leaves the workpiece more than 2 mm and the arc is extinguished.
7. When the main transformer temperature exceeds 110 °C due to the connection working time is too long, the thermal protection switch will operate and the device will automatically shut down and cannot be started. It should be restarted after the transformer has cooled down.
8. Always remove the accumulated water in the filter pressure reducing valve, that is, rotate the lowermost screw counterclockwise to remove the water and then tighten. If there is too much water in the compressed air, consider adding a filter valve between the filter pressure reducing valve and the gas source, otherwise the cutting quality will be affected.
9. When the workpiece is not cut, press the torch button as little as possible to avoid damage to the machine.
10. After the cutting workpiece is finished, cut off the power switch and the air supply valve.

Pvc Cutting Machine Picture

utomatic tape tape cutting machine ---

With the continuous development of industrial technology, traditional manual work such as cutting tape is now replaced by machines. Tape cutting machine is also called adhesive paper cutting machine and tape machine.

Cutting range:
Cutting length: between 3-999mm
Cutting width: between 3-100mm
Such an automatic adhesive tape cutting machine can be used in the production and packaging processes of electronics, machinery and other factories: labeling, fixing, etc., can greatly improve work efficiency, save labor costs, and ensure the quality of work.

Pvc Cutting Machine Picture

utomatic tape tape cutting machine ---

With the continuous development of industrial technology, traditional manual work such as cutting tape is now replaced by machines. Tape cutting machine is also called adhesive paper cutting machine and tape machine.

Features:
• The tape is automatically peeled off, cut according to the set length, and the cut tape is continuously and side by side attached to the edge of the rotating disk.
·The tape cutting length and the bonding interval can be adjusted at will according to the needs of the user.
·The cut surface of the tape is not jagged and very neat.
· The work of the production staff and the tape-cutting personnel can be completely replaced by one person, and it is more labor-saving and efficient.
·With a special tape cutter, it is possible to cut off the tape with a liner.
· Suitable for a variety of small adhesive tapes attached to the board.
· Unique conveyor system for multiple people to use at the same time.
· Small size, light weight and easy to carry.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com