Manual Adhesive Tape Slitting Machine

Manual Adhesive Tape Slitting Machine

Tape Cutting Machine-

Third, pay attention to the operation process:
1. The torch is in contact with the workpiece and can be cut by pressing the button. Cutting can be started from the edge of the workpiece. When the thickness of the sheet is not large, it can be cut at any point of the workpiece. The torch can be perpendicular to the workpiece
Or slightly inclined to one side, but when opening in the middle of the workpiece, the torch should be tilted slightly to one side in order to blow off the molten metal and cut through the metal.
2. Press the handle button and keep the main circuit on, while the high frequency oscillator works until the cutting arc is formed, and the high frequency oscillator stops working. Thereafter, the cutting can be performed by the movement of the torch. At the same time, the cutting indicator lights.
3. The cutting must be cut through the metal to move evenly, otherwise the nozzle will be damaged. Moving too fast or too slow will affect the quality of the cut.
4, cutting air pressure adjustment: cutting air pressure is too high, the flow is too large, will affect the cutting thickness. If the cutting air pressure is too small, it will affect the service life of the nozzle.
5. Before lifting the torch away from the workpiece, the handle button must be turned on. At this time, the plasma arc is extinguished and the cutting process is stopped.
6. During the cutting process, the arc is re-arced because the torch leaves the workpiece more than 2 mm and the arc is extinguished.
7. When the main transformer temperature exceeds 110 °C due to the connection working time is too long, the thermal protection switch will operate and the device will automatically shut down and cannot be started. It should be restarted after the transformer has cooled down.
8. Always remove the accumulated water in the filter pressure reducing valve, that is, rotate the lowermost screw counterclockwise to remove the water and then tighten. If there is too much water in the compressed air, consider adding a filter valve between the filter pressure reducing valve and the gas source, otherwise the cutting quality will be affected.
9. When the workpiece is not cut, press the torch button as little as possible to avoid damage to the machine.
10. After the cutting workpiece is finished, cut off the power switch and the air supply valve.

Manual Adhesive Tape Slitting Machine

GL-5000 tape cutter to cut two kinds of tape at the same time steps and precautions
If the tape width is less than 10 mm, insert the divider. This model can cut two tapes with a width of less than 25 mm at the same time.
1. Remove the divider from the bottom of the machine.
2. Press the press cover button to open the press cover.
3. If the tape width is less than 10 mm, insert the auxiliary spacer.
! Remove the auxiliary divider from the bottom of the machine and insert it into the junction of the divider.
4. Install the tape roll and move the width bar to adjust the tightness of the guide plate.
5. Import the tape and set the working mode.
! In the automatic mode, when cutting two sets of tape, take two pieces of tape and the machine will cut the two pieces of tape.
*note
1. Forcibly cutting high-adhesive tape will affect the service life of the motor.
2. After using the divider and auxiliary dividers, return to the bottom of the machine.

Manual Adhesive Tape Slitting Machine

GL-704 Four-shaft Auto Roll Cutting Machine

GL-704 Four-shaft Auto Roll Cutting Machine, Suitable for cutting BOPP tape, PVC insulation tape, masking tape, double sided tape, duct tape, medical tape, etc.

 

Product Description

1.Main Motor: Cutting shaft and circular blade are driven by A.C motor with inverter control, which able to set RPM and running direction obverse/reserve on different requests.

2. Central Control: Central control system is CPU, which can cut various sizes on one log roll by changing modes automatically.

3. Display Mode: All functions are operated under LCD touch panel control, which is operator friendly and easy for data setting.

4. Width Setting: Width setting is controlled by servomotor with ball screw and guide rails to make accuracy movement.

5. Cutting System: Knife feeding is controlled by servomotor, which can do three-speed cutting.

6. Knife Angle Adjustment: Cutting angle can be changed automatically for making roll surface smoothly.

7. Shaft Change: Three kinds of cutting shafts for optional using on this machine, which use quick changing shaft according to different material.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com