Fabric Slitter Machine

Fabric Slitter Machine

Tape Cutting Machine-

Third, pay attention to the operation process:
1. The torch is in contact with the workpiece and can be cut by pressing the button. Cutting can be started from the edge of the workpiece. When the thickness of the sheet is not large, it can be cut at any point of the workpiece. The torch can be perpendicular to the workpiece
Or slightly inclined to one side, but when opening in the middle of the workpiece, the torch should be tilted slightly to one side in order to blow off the molten metal and cut through the metal.
2. Press the handle button and keep the main circuit on, while the high frequency oscillator works until the cutting arc is formed, and the high frequency oscillator stops working. Thereafter, the cutting can be performed by the movement of the torch. At the same time, the cutting indicator lights.
3. The cutting must be cut through the metal to move evenly, otherwise the nozzle will be damaged. Moving too fast or too slow will affect the quality of the cut.
4, cutting air pressure adjustment: cutting air pressure is too high, the flow is too large, will affect the cutting thickness. If the cutting air pressure is too small, it will affect the service life of the nozzle.
5. Before lifting the torch away from the workpiece, the handle button must be turned on. At this time, the plasma arc is extinguished and the cutting process is stopped.
6. During the cutting process, the arc is re-arced because the torch leaves the workpiece more than 2 mm and the arc is extinguished.
7. When the main transformer temperature exceeds 110 °C due to the connection working time is too long, the thermal protection switch will operate and the device will automatically shut down and cannot be started. It should be restarted after the transformer has cooled down.
8. Always remove the accumulated water in the filter pressure reducing valve, that is, rotate the lowermost screw counterclockwise to remove the water and then tighten. If there is too much water in the compressed air, consider adding a filter valve between the filter pressure reducing valve and the gas source, otherwise the cutting quality will be affected.
9. When the workpiece is not cut, press the torch button as little as possible to avoid damage to the machine.
10. After the cutting workpiece is finished, cut off the power switch and the air supply valve.

Fabric Slitter Machine

GL-701P tape roll cutting machine

-------Cutting pvc tape, bopp tape,PE, PET, EVA, masking tape , foam tape ,double sided tape etc .


Product Description

1.   PLC with touch screen ,auto shifting of different cutting widths .

2.   Single shaft, single blade .

Fabric Slitter Machine

Tape cutting machine features ---

1. The tape cutting machine adopts no roller design, which is convenient for operation.
2, the maximum width of the cutting is 60mm (see machine parameters below), this must be understood before use, to see if it meets the width of the tape you want to cut.
3, tape cutting machine with memory function, according to the length of the tape cut usually from the set of six different cutting lengths, you can call directly after the need to set up.
4, install the tape, through the elastic film auxiliary shaft, so it is easier to fix the film to prevent the tape roll from falling.
5, tape cutting machine with counting function, you can set the amount to be cut.
6. Two rolls of tape can be used at the same time, but the total width should be within the width parameter of the tape cutter.
7. Be careful when taking the tape. Although the tape cutter is equipped with a protective device and a safety guard at the knife edge, try not to approach the knife edge.
8, accurate digital control cutting length, you can set the length you want to cut.
9. It is not necessary to adjust the tape cutter because of the thickness of the tape.
10. The tape cutting machine has built-in pliers, lubricating oil and partition for easy operation.
11, anti-static ABS material
12. Improve safety. When the warning device is operated and the tape cutter is suspended, even if the blockage is removed, the tape cutter will not operate immediately. You need to press the start button again to use it normally.


Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?