Manual Adhesive Tape Cutting Machine

Manual Adhesive Tape Cutting Machine

Tape Cutting Machine-

Third, pay attention to the operation process:
1. The torch is in contact with the workpiece and can be cut by pressing the button. Cutting can be started from the edge of the workpiece. When the thickness of the sheet is not large, it can be cut at any point of the workpiece. The torch can be perpendicular to the workpiece
Or slightly inclined to one side, but when opening in the middle of the workpiece, the torch should be tilted slightly to one side in order to blow off the molten metal and cut through the metal.
2. Press the handle button and keep the main circuit on, while the high frequency oscillator works until the cutting arc is formed, and the high frequency oscillator stops working. Thereafter, the cutting can be performed by the movement of the torch. At the same time, the cutting indicator lights.
3. The cutting must be cut through the metal to move evenly, otherwise the nozzle will be damaged. Moving too fast or too slow will affect the quality of the cut.
4, cutting air pressure adjustment: cutting air pressure is too high, the flow is too large, will affect the cutting thickness. If the cutting air pressure is too small, it will affect the service life of the nozzle.
5. Before lifting the torch away from the workpiece, the handle button must be turned on. At this time, the plasma arc is extinguished and the cutting process is stopped.
6. During the cutting process, the arc is re-arced because the torch leaves the workpiece more than 2 mm and the arc is extinguished.
7. When the main transformer temperature exceeds 110 °C due to the connection working time is too long, the thermal protection switch will operate and the device will automatically shut down and cannot be started. It should be restarted after the transformer has cooled down.
8. Always remove the accumulated water in the filter pressure reducing valve, that is, rotate the lowermost screw counterclockwise to remove the water and then tighten. If there is too much water in the compressed air, consider adding a filter valve between the filter pressure reducing valve and the gas source, otherwise the cutting quality will be affected.
9. When the workpiece is not cut, press the torch button as little as possible to avoid damage to the machine.
10. After the cutting workpiece is finished, cut off the power switch and the air supply valve.

Manual Adhesive Tape Cutting Machine

GL-706 circular balde tape roll cutting machine / adhesive tape cutting machine:

1. Application

suitable for cutting PVC tape,masking paper tape,double sided tape,kraft tape,conductive foam tape,duck tape,protective film, etc.

 

3. Main Features

1). High cutting precision

2). Big cutting roll diameter

3). All electric elements are famous brands

4). Taiwan shagyin Ball screw

5). 10 inch touch screen operation 

6). Different slitting width can be on same roller

7). Main roller, round blade, inlet blade, speed is adjustable

8). Round blade base is high precision

Manual Adhesive Tape Cutting Machine

GL-702 550mm cutter scotch tape production machine

 -Application 

suitable for cutting roll materials:such as BOPP, foam tape, masking tape, duct tape,double sided tape,cloth tape,industrial tape, protection film, roll papers etc.

-Main Features

1.  Main driving system: AC motor with inverter is employed. 

2. Operating panel:  All functions are operated on the 10" LCD touch panel.

3. Central control unit:   Programmable central control is used and 20 sizes can be set on the same shaft for auto transfer and cutting.

4.  Cutting positioning system: Cutting positioning is controlled by Mitsubishi servo motor.

    The imported high precision ball screw is applied to set the size and the linear slide rail is to bear the load of the cutter seat.

5. Blade feeding positioning system: Blade feeding is controlled by Mitsubishi servo motor, and the cutting speed is adjustable in three stages.

6. Auto angle adjustment of circular blade: Mitsubishi servo motor is used to calculate the circular blade angle and the angle change is subject to different materials (The angle change range is ±8°).

7. Quick shaft change system: Three kinds of shafts are available and quick change of shafts is applied for different materials.

 

 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com