Aluminum Foil Tape Cutting Machine

Aluminum Foil Tape Cutting Machine

Tape Cutting Machine-

Third, pay attention to the operation process:
1. The torch is in contact with the workpiece and can be cut by pressing the button. Cutting can be started from the edge of the workpiece. When the thickness of the sheet is not large, it can be cut at any point of the workpiece. The torch can be perpendicular to the workpiece
Or slightly inclined to one side, but when opening in the middle of the workpiece, the torch should be tilted slightly to one side in order to blow off the molten metal and cut through the metal.
2. Press the handle button and keep the main circuit on, while the high frequency oscillator works until the cutting arc is formed, and the high frequency oscillator stops working. Thereafter, the cutting can be performed by the movement of the torch. At the same time, the cutting indicator lights.
3. The cutting must be cut through the metal to move evenly, otherwise the nozzle will be damaged. Moving too fast or too slow will affect the quality of the cut.
4, cutting air pressure adjustment: cutting air pressure is too high, the flow is too large, will affect the cutting thickness. If the cutting air pressure is too small, it will affect the service life of the nozzle.
5. Before lifting the torch away from the workpiece, the handle button must be turned on. At this time, the plasma arc is extinguished and the cutting process is stopped.
6. During the cutting process, the arc is re-arced because the torch leaves the workpiece more than 2 mm and the arc is extinguished.
7. When the main transformer temperature exceeds 110 °C due to the connection working time is too long, the thermal protection switch will operate and the device will automatically shut down and cannot be started. It should be restarted after the transformer has cooled down.
8. Always remove the accumulated water in the filter pressure reducing valve, that is, rotate the lowermost screw counterclockwise to remove the water and then tighten. If there is too much water in the compressed air, consider adding a filter valve between the filter pressure reducing valve and the gas source, otherwise the cutting quality will be affected.
9. When the workpiece is not cut, press the torch button as little as possible to avoid damage to the machine.
10. After the cutting workpiece is finished, cut off the power switch and the air supply valve.

Aluminum Foil Tape Cutting Machine

Tape Cutting Machine Usage:

The machine is suitable for cutting BOPP tapes, PVC tapes, PE tapes, masking paper tapes, double sided tapes, kraft paper tapes, foam tapes, duct tapes, industrial tapes, protective film, etc.

 

 

tape cutting machine Main Features:

1) Easy to operate.

2) Silicon solution cooling system, avoiding cutter getting sticky which can make sure that the cutting process are all right.

3) Accurate cutting position: using servo motor to drive, used with perfect ball screw, lineary or bit to make sure the cutting process accurate and perfect.

4) The face and back tube are supported by oil pressure to ensure the stability of mini pathway when it was cut.

5) Round knife cutting promotes the working efficiency.

Aluminum Foil Tape Cutting Machine

Guolian tape slitting machine configuration instructions:
The central panel is easy to operate. Suitable for BOPP tape and all single-sided tape slitting.

1. This machine adopts Mitsubishi PLC control, LED touch screen displays input data.

2. AC motor drive, variable frequency speed control running speed, can effectively protect electrical components.

3. Magnetic braking, smooth braking.

4. The single-roll tape uses a silicone roller; the winding is free of air bubbles. Specializing in the production of ultra clear transparent tape.

5. Single-roll tape uses a precision pressure regulator to control pressure stability.

6. Automatic rewinding side material

8. Stop the machine automatically when the side material breaks

9. Plus hydraulic automatic feeding device

10. Do not stop automatic labeling

11. The two motors work together and the shaft is replaced efficiently without stopping the machine.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com